Maintenance - Conrad 640579 Bedienungsanleitung

Assigning a transmitter
a) Assignment using the blind actuator
• Press the control key (B) on the blind actuator for longer than 2 seconds, until the control LED (A) flashes.
• Within 15 seconds, press the "On" button of a switch channel on a wireless wall transmitter or a remote
control device (e.g. marked "ON" or "l") for at least 3 seconds, until the motor connected to the blind actuator
briefly runs in both directions and stops again. This indicates that the programming is correct.
Then the motor can be controlled with the "ON" and "OFF" buttons of the already programmed switch chan-
nel; see chapter "Moving the blind." Briefly pressing the respective other button stops the blind motor.
• The programming/assigning mode will end automatically. If you wish to assign further wall transmitters or
remote controls (a maximum of 10 are possible), then proceed again as described above.
You can also assign several switching channels to the same transmitter. With a 4-channel re-
mote control, for example, Channel 1 can control the blind in the kitchen, Channel 2 the blind in
the living room and Channel 3 can operate both blinds at the same time.
b) Assignment using an already assigned transmitter
• Press both buttons of an already assigned switch channel on a transmitter at the same time and hold for
at least 3 seconds.
Make sure the two push buttons are for the same switching channel.
• The control LED (A) flashes (possibly not visible, since the blind actuator is installed in the flush-mounted
socket).
• Now pick up the wall transmitter or the remote control that you want to reassign. Within 15 seconds, press
and hold the "On" button of the switching channel there (e.g. labelled "ON" or "I") for at least 3 seconds.
If you wait too long to report a new transmitter (longer than 15 seconds), the blind actuator
leaves the learning mode automatically. In this case, start the learning mode again as described
above.
The blind motor will move briefly in both directions and then stop. This indicates that the programming is
correct.
• The programming/assigning mode will end automatically. If you wish to assign further wall transmitters or
remote controls (a maximum of 10 are possible), then proceed again as described above.
You can also assign several switching channels to the same transmitter. With a 4-channel re-
mote control, for example, Channel 1 can control the blind in the kitchen, Channel 2 the blind in
the living room and Channel 3 can operate both blinds at the same time.
Deleting a single switch channel/transmitter
If the blind actuator is no longer appropriate for a switch channel / transmitter (e.g. if you want to use the switch
channel for a different wireless receiver in the RSL system), the switch channel can be deleted from the blind
actuator's registry.
a) Deletion using the blind actuator
• Press the control key (B) and hold for longer than 2 seconds, until the control LED (A) flashes.
• Press the "ON" or "OFF" button of an already assigned switch channel on a wireless wall transmitter or a
remote control device that you wish to delete until the control LED (A) light goes out.
The blind motor will move briefly in both directions and then stop. This indicates that the deletion has been
carried out successfully.
b) Deletion using a transmitter
• Press both buttons of the already assigned switch channel of the transmitter that you wish to delete and
hold for at least 3 seconds.
Make sure the two push buttons are for the same switching channel.
• The control LED (A) flashes (possibly not visible, since the blind actuator is installed in the flush-mounted
socket).
• Press the "ON" or "OFF" button of an already assigned switch channel on a wireless wall transmitter or a
remote control device that you wish to delete until the control LED (A) light goes out.
The blind motor will move briefly in both directions and then stop. This indicates that the deletion has been
carried out successfully.
Deleting all assigned switch channels/transmitters
• Press the control key (B) and hold for longer than 2 seconds, until the control LED (A) flashes. Then
release the button.
• Press the control key (B) and hold for longer than 2 seconds, until the control LED (A) goes out.
The blind motor will move briefly in both directions and then stop. This indicates that the deletion has been
carried out successfully.
Then all assigned switch channels/wireless transmitters are deleted; the blind actuator does not react to
any existing transmitter of the RSL system and must be reprogrammed.
Reversing the rotation direction
• Press the control key (B) briefly. The blind motor runs a short way in both directions and then stops.
• Now shortly press the "ON" or "OFF" button on an assigned switch channel/transmitter.
• The direction of rotation is now reversed (this applies for all assigned switch channels at once, as well as
for a possibly connected blind button).
Moving the blind
To move the blind up: Press the "S" (up) button on a connected blind button or the "ON" or "I" button
of the assigned switch channel of a transmitter briefly.
To move the blind down: Press the "F" (down) button on a connected blind button or the "OFF" or "O"
button of the assigned switch channel of a transmitter briefly.
To stop the blind: Briefly press whichever button indicates the opposite direction of the one the
blind is moving in.
The maximum motor run time is approx. 90 seconds; after this, the blind actuator switches off
automatically.
The blind actuator cannot detect the end position of the blind. This must be either contained in
the motor or in a corresponding control.
The rotation direction can be reversed; see the section: "Reversing the rotation direction".

Maintenance

The product does not require any maintenance and should never be opened or disassembled for any reason.
Repair or maintenance work must be carried out by a specialist.
Information about the transmission range
Dependent on the type of wireless transmitter you use, the range is up to 70 m.
This value, however, is the so-called "open space range" (the range when the transmitter and
receiver are visible to each other, without disturbing influences).
In practice, however, there may be walls, room ceilings etc. between the transmitter and the
receiver which reduce the range accordingly.
Due to the different influences on the wireless transmission, no specific range can be guaran-
teed. However, trouble-free operation is usually possible in a single family house.
The range can sometimes be limited considerably by:
• Walls, reinforced concrete ceilings
• Coated / metallised insulating glass
• Proximity to metal & conducting objects (e.g., radiators)
• Proximity to human bodies
• Broadband interferences, e.g. in residential areas (DECT telephones, mobile phones, radio-controlled
headphones, radio-controlled speakers, radio-controlled weather stations, baby phones etc.)
• Proximity to electric motors, transformers, power-supply units, computers
• Proximity to badly shielded or uncovered computers in use or other electrical appliances
Declaration of Conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this product
conforms to the fundamental requirements and the other relevant regulations of the directive 1999/5/EC.
The Declaration of Conformity for this product can be found at www.conrad.com.
Disposal
Dispose of an unserviceable product in accordance with the relevant statutory regulations.
Technical data
Operating voltage ......................................... 230 V/AC, 50 Hz
Electrical/ motor capacity .............................. up to max. 500 VA
Number of motors that can be connected .... 1
Reception frequency ..................................... 433 MHz
Transmission range ...................................... Max. 70 m (see chapter "Range")
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau
(www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited. This publication represent the technical status at the time of
printing.
© Copyright 2015 by Conrad Electronic SE.