Grundig FINE ARTS VISION MFW 82-725/9 DVD Serviceanleitung Seite 33

GRUNDIG Service
Alignment
8. Picture Call up the "Picture sharpness P. 1...199" menu via
sharpness "EASY DIALOG" –> "Installation" –> "Special functions"
(to page 2).
9. White level Feed in a grey scale test pattern with burst.
White balance:
Contrast:
Colour contrast:
Screen brighness:
Call up the "White level alignment" menu via "EASY
DIALOG" –> "Installation" (to page 2) –> "Dealer service
menu" –> "8500" –> "Picture settings".
10. Picture tube Call up the "Picture tube type" menu via "EASY
type DIALOG" –> "Installation" (to page 2 / option) –> "Dealer
service menu" –> "8500" –> "Special functions".
11. PIP position Feed in a transmitter picture.
Press and hold down the "PIP" button while switching on
with the mains switch.
12. Screen Call up the "Screen geometry" menu via "EASY DIALOG" –>
geometry "Installation" (to page 2) –> "Dealer service menu" –>
"8500".
Feed in a geometry test pattern.
Attention: The "Horiz. Pos." alignment influences the
horizontal phase. Prior to carrying out this adjustment, set
the picture width to minimum and correct the lock-in position
if necessary using the "H-Shift" plug.
Reset: The "Reset" field contains:
- either the optimum picture geometry data set at the
factory,
- or an average data record from the ROM if the set has
been started with the emergency data record.
After an incorrect alignment you may reload this basic data
at any time:
Call up the "Reset" menu via "EASY DIALOG" –>
"Installation" (to page 2) –> "Dealer service menu" –>
"8500" –> "Screen geometry".
Screen Switch the set to channel position "AV5" and feed in a
geometry geometry test pattern via the VGA socket.
VGA Call up the "Reset" menu via "EASY DIALOG" –>
"Installation" (to page 2) –> "Dealer service menu" –>
"8500" –> "Screen geometry".
Screen Call up the "TeleWeb" menu via "EASY DIALOG" –>
geometry "Installation" –> "TeleWeb" –> "TeleWeb".
TeleWeb Select "On".
Call up the "Installation – Dealer service menu" menu via
"EASY DIALOG" –> "Installation" (to page 2) –> "Dealer
service menu" –> "8500", and exit the menu by pressing the
" " button.
Call up the "Screen geometry" menu via "EASY DIALOG"
–> "Info" –> "TeleWeb" –> picture format button "
Ending the geometry alignment:
Use the " " button to call up the "TeleWeb functions" menu,
and exit the menu via the "Exit" menu item.
Preparations
Central position
Maximum
Mean value
Mean value
i
".
2 - 5
Alignment procedure
Adjust picture for best sharpness ("manual" or "0...3").
The channel positions 1...199 are adjusted at the same
time.
Adjust the values for red, green and blue so that the
picture becomes achromatic.
Set the picture type (T=Toshiba, P=Philips, V=Videocolor).
(This effects the peak beam current).
Adjust the vertical and horizontal PIP position so that the
small picture is not confined by the picture borders.
With the help of the user guide adjust the geometry values
first for the vertical deflection and then for the horizontal
deflection.
Only when this is done position the picture contents into the
centre of the screen. Re-adjust the picture width according
to the test pattern.
Saving:
The set value is saved by pressing the "yellow" button.
The picture geometry adjusts itself to the last saved value
when switching the TV set on again.
Check the geometry via the menu guide and correct it if
necessary.
Saving:
The set value is saved by pressing the "yellow" button.
The picture geometry adjusts itself to the last saved value
when switching the TV set on again.
Following the Geometry menu guide and referring to the
displayed geometry test pattern, check the picture geometry
and align it if necessary.
Saving:
The set value is saved by pressing the "yellow" button.
The picture geometry adjusts itself to the last saved value
when switching the TV set on again.
DIGI 100