Intended Use; Operating Elements - VOLTCRAFT VC-230 Bedienungsanleitung

Intended Use

- Measuring and displaying electric parameters in the range of excess voltage category III (up to max. 600V against
ground potential, pursuant to EN 61010-1) and all lower categories.
- Measuring direct current up to max. 1000 V (CAT II)
- Measuring alternating current up to max. 750 V (CAT II)
- Measurement of direct and alternating current up to 10 A
- Frequency measuring up to 10 MHz
- Capacity measuring up to 100 µF
- Measurement of resistance values of up to 40MOhm
- Continuity check (< 70 Ohm acoustic)
- Diode test
The two current measuring inputs are secured against overload. The voltage in the measuring circuit may not exceed
250 V. The 10 A measuring range is equipped with a fine fuse, the 400 mA measuring range with a self-resetting PTC
fuse.
The device may only be operated with the specified batteries.
The measuring instrument must not be operated when it is open, i.e. with an open battery compartment or when the
battery compartment cover is missing. Measuring in damp rooms or under unfavourable ambient conditions is not
admissible.
For safety reasons, when measuring only use measuring cables or accessories which are adjusted to the specifica-
tions of the multimeter.
Unfavourable ambient conditions are:
- Wetness or high air humidity
- Dust and flammable gases, vapours or solvents
- thunderstorms or similar conditions such as strong electrostatic fields etc.
Any use other than the one described above damages the product. Moreover, this involves dangers such as e.g. short
circuit, fire, electric shock, etc. No part of the product must be modified or rebuilt!
The safety instructions must be followed unconditionally!

Operating elements

1 Detachable rubber holster
2 LC display with connection information
3 REL button for relative measuring function
4 Rotary switch
5 mAµAHz measuring socket (with self-resetting fuse)
6 10 A measuring socket (with fine-wire fuse)
7 VΩ capacity measuring socket (with commensurability „+")
8 COM measuring socket (reference potential)
9 SELECT button for function switching
10 Low imp. 400 kΩ button for short-time reduction of the measuring impedance from 10 MOhm to 400 kOhm
20
Inleiding
Geachte klant,
hartelijk dank voor de aankoop van dit Voltcraft® product. U heeft hiermee een goede keus gedaan.
U heeft een kwaliteitsproduct aangeschaft dat ver boven het gemiddelde uitsteekt. Een product uit een merkfamilie
die zich op het gebied van meet-, laad-, en voedingstechniek onderscheidt door specifieke vakkundigheid en perma-
nente innovatie.
Met Voltcraft® kan zowel de ambitieuze hobby-elektronicus als de professionele gebruiker ingewikkelde taken uit-
voeren. Voltcraft® biedt u betrouwbare technologie met een buitengewoon gunstige verhouding van prijs en presta-
ties.
Wij zijn ervan overtuigd: uw start met Voltcraft tegelijkertijd het begin van een lange en goede samenwerking zal zijn.
Veel plezier met uw nieuw Voltcraft® product!
Inhoudsopgave
Inleiding ......................................................................................................................................................................49
Voorgeschreven gebruik..............................................................................................................................................50
Bedieningselementen..................................................................................................................................................50
Veiligheidsvoorschriften ..............................................................................................................................................51
Productbeschrijving ....................................................................................................................................................52
Leveringsomvang ........................................................................................................................................................53
Displaygegevens en symbolen....................................................................................................................................53
Meetbedrijf ..................................................................................................................................................................54
a) Spanningsmeting „V" ........................................................................................................................................54
b) Stroommeting „A" ............................................................................................................................................ 55
c) Frequentiemeting ..............................................................................................................................................56
d) Weerstandsmeting ............................................................................................................................................56
e) Diodetest ..........................................................................................................................................................57
f) Doorgangstest ..................................................................................................................................................57
g) Capaciteitsmeting..............................................................................................................................................58
RELΔ-functie ..........................................................................................................................................................58
Low Imp. 400 kΩ-functie ........................................................................................................................................58
Auto-Power-Off-functie ..........................................................................................................................................58
Onderhoud en reiniging ..............................................................................................................................................59
Algemeen................................................................................................................................................................59
Reiniging ................................................................................................................................................................59
Vervangen van de 10 A-zekering............................................................................................................................59
Plaatsen en vervangen van de batterij ..................................................................................................................60
Afvoer van lege batterijen! ......................................................................................................................................60
Verwijderen..................................................................................................................................................................61
Verhelpen van storingen..............................................................................................................................................61
Technische gegevens ................................................................................................................................................62
49