Herunterladen Inhalt Inhalt Diese Seite drucken

Grundig CHALLENGE 600 CD Service Anleitung Seite 4

Vorschau ausblenden Andere Handbücher für CHALLENGE 600 CD:
Inhaltsverzeichnis

Werbung

Allgemeiner Teil / General Section
4. CD-Leiterplatte ausbauen
- CD-Laufwerk ausbauen (Pkt. 1).
- 3 Steckverbinder K abziehen (Fig. 8).
- 2 Schrauben L herausschrauben (Fig. 8).
- Leiterplatte aus der Halterung ziehen und vorsichtig (Flexprint!)
anheben.
- Flexprinthalter öffnen 1 (Fig. 9).
- Achtung: Die Lasereinheit ist sehr empfindlich gegen stati-
sche Aufladungen (MOS-Bauteile)!
Schließen Sie deshalb die Flexprintleitung zur Lasereinheit vor
dem Abziehen mit einer Büroklammer kurz (Fig. 10).
- Flexprint aus dem Flexprinthalter ziehen 2 (Fig. 9).
N
M
L
Fig. 8
5. Pick-Up-Einheit ausbauen
- CD-Laufwerk ausbauen (Pkt. 1).
- CD-Leiterplatte ausbauen (Pkt. 4).
- 2 Schrauben M herausschrauben und Abdeckung N abnehmen
(Fig. 8).
- Schraube O herausschrauben und den Schalter P abnehmen
(Fig. 11).
- 4 Schrauben Q herausschrauben (Fig. 11) und die Pick-Up-Einheit
herausnehmen.
6. Schlitten-Motor ausbauen
- CD-Laufwerk ausbauen (Pkt. 1).
- Pick-Up-Einheit ausbauen (Pkt. 5).
- Schraube R herausschrauben und die Blattfeder S herausnehmen
(Fig. 11).
- Spindel T und Zahnrad U in Pfeilrichung herausziehen (Fig. 11).
- 2 Schrauben V (Fig. 11) herausschrauben und den Motor abneh-
men.
1 - 4
M
K
L
Q
T
N
Q
Fig. 11
4. Removing the CD PCB
- Remove the CD Drive (para 1).
- Open 3 connectors K (Fig. 8).
- Undo 2 screws L (Fig. 8).
- Pull the PCB out of its holder and lift it carefully (flexprint!).
- Open the flexprint holder 1 (Fig. 9).
- Attention: The laser unit is very sensitive to static charges
(MOS components)!
Therefore, short-circuit the flexprint to the laser unit with a metal
paper clip before disconnecting it (Fig. 10).
- Pull the flexprint out of its holder 2 (Fig. 9).
1
Fig. 9
Fig. 10
5. Removing the Pick Up Unit
- Remove the CD Drive (para 1).
- Remove the CD PCB (para 4).
- Undo 2 screws M and remove the cover N (Fig. 8).
- Undo screw O and take away the switch P (Fig. 11).
- Undo 4 screws Q and remove the Pick Up Unit.
6. Removing the Sled Motor
- Remove the CD Drive (para 1).
- Remove the Pick Up Unit (para 5).
- Undo screw R and remove the plate spring S (Fig. 11).
- Pull out the spindle T and the gear wheel U in direction of the arrow
(Fig. 11).
- Undo 2 screws V (Fig. 11) and remove the motor.
V
U
S
R
Q
O P
SCD 3390 RDS / Challenge 600 CD
2
GRUNDIG Service

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Scd 3390 rds

Inhaltsverzeichnis