Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL BT-PO 1100/1 E Betriebsanleitung

Anleitung_BT_PO_1100_1_E_SPK1:_
that the attachments are securely installed.
Never touch the area you wish to polish with the
edge of the sanding/grinding disk.
Use the speed selector (Fig. 3/Item 4) to select the
following maximum speeds for polishing:
- Working in polish:
- Polishing to a high gloss: approx. 1000-1100 rpm
- Polishing up:
If you do not comply with these instructions, the
manufacturer cannot accept any liability.
The Velcro fastener enables easy changing of the
polishing attachment.
- Use the foamed plastic attachment to apply the
polishing agent (Fig. 8).
Make sure that the foamed plastic attachment is
free of any foreign bodies.
Spread the polishing paste evenly over the
polishing pad. Do not apply the polish directly to
the polishing surface.
Switch the polishing machine on and off only
when the polishing machine is resting on the
polishing surface.
Place the extension lead over your shoulder and
work first on the large, flat surfaces such as the
bonnet, boot lid and roof.
Keep your movements as regular as possible.
Important! Allow the polishing machine to glide
over the polishing surface. Do not exert pressure!
Work next on the smaller surfaces (doors, for
example)
- Use the fleece attachment to finish off the polishing
(Fig. 9).
Make sure that the fleece attachment is free of all
foreign bodies.
Remove the layer of polish in the same order as it
was applied.
Important! Do not exert pressure on the
polishing machine!
Care tips
For optimum paintwork protection, you should
polish your car 2 to 3 times a year.
Wash your car at least every 2 weeks. Avoid
using household detergents as these can damage
the paintwork and remove the layer of wax.
Wash your car with a clean sponge, working from
top to bottom.
Remove all insects, bird droppings and tar stains
from the paintwork daily.
If you use any window-cleaning agents, spray
them onto a cloth and not directly onto the
windows in order to prevent them wetting the
paintwork.
19.04.2011 10:10 Uhr
7.3 Using as a sanding machine
Use the supplied sanding attachments (Fig. 10) for
sanding purposes.
The Velcro fastener enables easy changing of the
sanding attachments.
Place the whole surface area of the sanding disk
approx. 1000 rpm
on the material.
Switch on the machine and move it with gentle
approx. 1400 rpm
pressure over the workpiece completely circular
movements or moving it to and fro and up and
down.
Use a coarse paper for coarse sanding and a
finer paper for finish sanding. You can find the
best paper for the job by means of testing.
7.4 Speed Control (Fig. 3)
Use the speed control to set the desired working
speed.
Press the "+" button to increase the speed.
Press the "-" button to decrease the speed.
Refer to the display (8) for the set speed.
Set speed = Display x 100

8. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
9. Cleaning, maintenance and ordering
of spare parts
Always pull out the mains power plug before starting
any cleaning work.
9.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.
Wash the polishing attachments only by hand and
let them air-dry. Use only a mild soap and a damp
cloth.
Seite 13
GB
13