Audio Setting; System Information - Yamaha BD-S1067 Bedienungsanleitung

■ Audio Setting

The default settings are marked with "
Audio Output
Coaxial/Optical
You can select the output mode of COAXIAL jack and
OPTICAL terminal. For more details on output formats,
refer to "About the audio output formats" (p. 34).
Outputs digital signal without any processing.
Bitstream
Secondary Audio is not output.
PCM Outputs 2-channel PCM.
* Outputs Bitstream with Secondary Audio. The audio
Reencode
signal is output in DTS signal.
Off
Mutes sound.
HDMI
You can select the output mode of HDMI ternminal. For
details on setting items, see "Coaxial/Optical" (p. 33). For
more details on output formats, refer to "About the audio
output formats" (p. 34).
Bitstream * , PCM, Reencode, Off
Note
– To output HD audio (such as Dolby TrueHD or
DTS-HD Master Audio) from HDMI terminal, set
Resolution to Auto or more than 720p (p. 31).
Downsampling
You can select digital audio signal down-sample
frequency. This function is effective for the audio signal
output from the COAXIAL jack/OPTICAL terminal.
48k * The highest sampling rate of digital PCM output is
48 kHz.
96k The highest sampling rate of digital PCM output is
96 kHz.
192k The highest sampling rate of digital PCM output is
192 kHz.
DRC
You can set the DRC (Dynamic Range Compression)
(p. 40) to on/off/Auto. When set to Auto, DRC is
automatically turned on for a source with DRC
information in Dolby TrueHD format. DRC makes the
strong sound such as plosive sound lower, and
conversations more audible. It is useful when you watch
movies in the night.
*
Off , On, Auto
SACD Output
SACD Priority
You can select a content played back from multi-channel
or stereo (2-channel) contents when a Hybrid SA-CD
(p. 4) including both is loaded.
Multi-ch * , 2-ch
HDMI Output
You can select audio signal output from HDMI terminal
* ".
when SA-CD is played back.
DSD
PCM
Speaker Setting
Configuration
You can set the output of 7.1 ch surround depending on
the connected speaker or amplifier.
1 Press 5/a to select a speaker you want to configure,
then press ENTER.
2 Adjust the figures below. Note that some of items are
not displayed depend on the selected speaker.
Size
Trim
Delay
Disable
3 Press RETURN to go back to speaker selection.
2ch Downmix
You can select down mix method to analog 2-ch from
Stereo or Lt/Rt.
Stereo
Lt/Rt
Post Process
You can multi-channelize the 2-channel audio signal. To
multi-channelize, select NEO6, then select Cinema or
Music mode.
*
Off , NEO6

■ System Information

Software version and MAC address (p. 41) are displayed.
*
Outputs DSD raw signal. When this Player is
connected to DSD compatible AV receiver, this item
is recommended.
Outputs PCM signal decoded by this Player.
When the woofer section of a speaker is 16 cm (6-1/
2 in) or larger, select Large. When smaller than 16
cm (6-1/2 in), select Small.
*
Large , Small
-12 to 0 dB (in 0.5 dB step)
The default setting is 0 dB.
0.5 to 10 m (in 0.5 m step)
The default setting is 3 m.
When selected speaker is not in use, select Yes.
*
Yes, No
* Changes channel output to stereo, which only
delivers sound from the two front speakers.
Select this item if this unit is connected to a Dolby
Pro Logic decoder. Sound from rear speakers is
mixed to the 2 ch stereo sound.
SETUP MENU
4
33
En