Automatic Power Off - Pioneer PDP-503MXE Bedienungsanleitung

Operations

Automatic Power OFF

This display is equipped with automatic power-
management and auto-power-off functions, which allow
the unit to automatically switch to power-saving mode
when no sync signal is detected.
(A warning message appears onscreen before these
functions operate.)
Notes
÷ The Power Management function can be set only when the
INPUT 1 signal is selected.
÷ The automatic power-off function can be set only when the
INPUT 2 signal is selected.
÷ Always turn off the plasma display's main power switch when
not using the display for extended periods of time.
1
Press MENU to display the menu screen.
MAIN MENU
PICTURE SCREEN
:
CO NT RA S T
:
BR I GHT .
: 6
+
R L E V E L .
: 6 0
+
G L E V E L .
: 6 0 +
B L E V E L .
:
H E NH AN CE .
:
V E NH AN CE .
R S E T E
SELECT
SET
2
Press 2/3 to select SET UP.
[When using INPUT 1]
MAIN MENU
PICTURE SCREEN
I N P UT L A B E
POWE R M NA GEME A
C L AMP P S I T I O N O
S E T T I N G
SELECT
SET
[When using INPUT 2]
MAIN MENU
PICTURE SCREEN
I N P UT L A
A U T O P OWE R
C L AMP P S I T I O N O
S E T T I N G
SELECT
SET
24
En
INPUT1
SET UP OPTION
0
0
0
0
0
ENTER EXIT
MENU
INPUT1
SET UP OPTION
:
L I N P UT 1
:
NT OF F
: A U T O
: V G A
ENTER EXIT
MENU
INPUT2
SET UP OPTION
:
B E L I N P UT 2
:
O F F O F F
: A U T O
: V G A
ENTER EXIT
MENU
3 Press 5/∞ to select either the POWER
MANAGEMENT or AUTO POWER OFF mode.
[When using INPUT 1]
MAIN MENU
PICTURE SCREEN
I N P UT L A B E
POWE R M NA GEME A
C L AMP P S I T I O N O
S E T T I N G
SELECT
SET
[When using INPUT 2]
MAIN MENU
PICTURE SCREEN
I N P UT L A
A U T O P OWE R
C L AMP P S I T I O N O
S E T T I N G
4
Press SET to confirm selection of the POWER
MANAGEMENT or AUTO POWER OFF.
3 OFF
ON 2
÷ When OFF is selected, the display will continue in
operating mode, regardless of the presence/
absence of an input sync signal.
÷ When POWER MANAGEMENT: ON is selected, if
a sync signal is not detected, a warning message is
displayed for 8 seconds, after which the display
automatically enters the power-saving mode (*1)
and the STANDBY/ON indicator flashes green. If a
sync signal (*2) is input again later, the plasma
display automatically returns to normal operating
mode.
*1. Power consumption about 1W
*2. Except when input signal is SYNC on G or composite
SYNC
÷ When AUTO POWER OFF: ON is selected and if no
sync signal is detected for 8 minutes or more, a
warning message will be displayed for 30 seconds
after which the unit's power will switch to
STANDBY mode.
5
When the setup is finished, press MENU to exit
the menu screen.
Note
The POWER MANAGEMENT and AUTO POWER OFF functions
must be set individually for each input (INPUT 1 or INPUT 2).
To return to operating mode:
÷ To return to normal operation from POWER
MANAGEMENT mode: either operate the computer,
or press INPUT on the Main Unit Operating Panel or
remote control unit.
÷ To return to normal operation from AUTO POWER
OFF mode: Press STANDBY/ON on the Main Unit
Operating Panel or remote control unit.
INPUT1
SET UP OPTION
:
L I N P UT 1
:
NT OF F
: A U T O
: V G A
CHANGE EXIT
MENU
INPUT2
SET UP OPTION
:
B E L I N P UT 2
:
O F F O F F
: A U T O
: V G A