Alarm; Motion; Alarm Set - Monacor AHR-40 Bedienungsanleitung

User Name: Input a user name registered before applying for
a domain name.
Password: Input a password you set when registering a user
name.
Click [Apply] button and restart the DVR; and then enter the
domain name (such as: http: // superdvr.3322.org:8080) to visit
your remote DVR.

6.2.5 Alarm

6.2.5.1 Motion

Click [Main menu  Alarm  Motion] to enter into the inter-
face shown as fig. 6-47.
Channel: Allow you enable/disable the motion function for
any channel.
Area: Click the [Setup] button to enter into area setup inter-
face shown as fig. 6-47.
The channel will be separated into a 44 × 36 grids (PAL / NTSC
mode). When any object moves into the motion detection area,
and the area where the object is located is displayed in red
and motion detection will be triggered. In the semi-transparent
area the motion detection is not activated.
Sensitivity: Allow you to set sensitivity level of motion de-
tection from higher to low with 8 being the most sensitive.
Alarm out: When this option is tick-selected, the alarm sen-
sor connected to the contacts "Alarm" (27) will sound when
motion is detected.
Latch time: You can set the duration of an alarm for a motion
detected (10 s, 30 s, 40 s, 60 s).
Show Message: You can set show message on the screen
when motion alarm is detected.
Buzzer time: You can set how long the buzzer will sound
when motion is detected (off, 10 s, 30 s, 40 s, 60 s).
Send Email: Allows you set the alarm images is issued to a
specified email.
Full screen Alarm: The function is defaulted to "On". When
the motion is detected, the corresponding channel will be
switched to the full screen mode.
Fig. 6-38
Fig. 6-39
Record Channel: The record channel will be activated when
the object move is detected.
Post Recording: You can set how long alarm record will last
when alarm ends (30 s, 1 minutes, 2 minutes, 5 minutes).
Copy: Allow you copy current channel parameters to any other
channel or all channels.
After configuring the above parameters, click <OK> to save it.

6.2.5.2 Alarm Set

Click [Main Menu  Alarm  Alarm] to enter into the below
window shown as fig. 6-40. Now you can perform alarm set
based on different status. Details please refer to list fig. 6-41.
Alarm In: Allow you select one desired channel.
Alarm Type: Contact type of the alarm sensor connected
NO (Normal Open) – The alarm will be triggered when the
contact is closed.
NC (Normal Close) – The alarm will be triggered when the
contact is opened.
OFF – No alarm will be triggered.
Alarm Out: When this option is tick-selected, the alarm sen-
sor connected to the contacts "Alarm" (27) will sound in the
event of an alarm.
Latch time: You can set the duration of the alarm (10 s, 20 s,
40 s, 60 s).
Show Message: You can set show message on the screen
when sensor alarm is detected.
Buzzer time: You can set if or how long the buzzer shall sound
in the event of an alarm (Off, 10 s, 20 s, 40 s, 60 s).
Send Email: Allows you set the alarm images is issued to a
specified email.
Full screen Alarm: The function is defaulted to "On". When
the motion detection or external alarm is triggered, the cor-
responding channel will be switched to the full screen mode.
Record Channel: Allow you select channels you want to record.
Post Recording: You can set how long alarm record will last
when alarm ends (30 s, 1 minute, 2 minutes, 5 minutes).
Copy: Allow you copy all the setting of one channel to other
ones.
Alarm Type Function
When an object moves into motion detection area, alarm
Motion
will be triggered. You can adjust sensitivity level to suit the
Detection
needs of your actual application environment.
External By means of external sensors connected, an alarm can be
alarm signal triggered and alarm recording can be started.
Fig. 6-41
Fig. 6-40
43