Inhaltsverzeichnis
Werbung
5. Immediate Recording
Entering a Stop Time
If a stop time is not entered, after a short time the display
will switch to the hours/minutes indication and the recor-
der will continue to record until it reaches the end of the
tape.
When it reaches the end, the recorder will automatically
rewind the tape to the beginning and then switch to stop.
There are two methods of entering the stop time:
Entering the stop time to the exact minute;
Entering the stop time in 30-minute steps.
Entering the stop time to the exact minute
Enter the stop time as a four-digit number with the numbered
1
0
¶
buttons
...
and confirm by pressing the
button.
OK
In the display will see the remaining playing time, then the
elapsed laying time, the programme position and the station
identification abbreviation.
Entering the stop time in 30-minute steps
Enter the desired stop time by repeaedly pressing the
M
;
buttons on the remote control or the
RECORD
M ;
buttons on the recorder (max.10 times = 300 minu-
tes).
Changing the stop time
If you wish to change the stop time while recording, press
M
;
both of the
buttons on remote control or the
RECORD
M ;
buttons on the recorder, enter the desired stop time
1
0
with the numbered buttons
...
and confirm this entry
by pressing the
¶
button, or press both of the
OK
M
;
buttons on the remote control or both of the
RECORD
M ;
buttons on the recorder until the desired stop time
is displayed.
Interrupting the Recording (Pause)
K
Press the
button during playback.
The indication "II" also appears in the display of the recorder.
K
Press the
button to continue recording.
The indication "II" disappears from the display.
The recording-pause function is limited to a certain time.
After this time, the recorder will switch to stop.
Terminating Recording Immediately
`
Press the
button to terminate recording.
Recording a Title Line
Title lines can be recorded.
Press the
button before or during recording to add the
*
title line to the recording.
To suppress the title line, press the
button again.
*
Assembling Recordings with Clean Joints
(Assembly Editing)
During playback, locate the tape position where you wish to
K
join the new recording, then press the
button.
Switch the recorder to recording-pause by pressing the two
M
;
buttons on the remote control, or press the
RECORD
M;
buttons on the recorder, and enter the desired pro-
gramme as one or two digits with the numbered buttons
1
...
0
.
K
Start the "new" recording by pressing the
button.
When you play the assembled recordings back, you will see
smooth joints without any flaws. This is called assembly edit-
ing.
6.1 Record Programming
for sets with ShowView
Programming with the VIDEO Plus+ System,
Enter the data as described in chapter 2.1 so that the recorder
can evalnate the ShowView.
Preparation
Insert a cassette with sufficient recording time and which is
not protected against recording.
Programming example
Press these buttons on the remote
You will see this in the display of the
control
remote control
1. Programming start
¶
,
- - - - -
–– ––
2. Enter the VIDEO Plus+ number
code for the desired TV programme
1
0
...
,
7654 -
–– ––
Check time and date.
Explanations
VG400024
The remote control is ready for data
entry.
1
2
3
4
5
6
7
8
9
0
SAT
Enter the VIDEO Plus+ number code in
the same sequence as given in the pro-
gramme journal.
If you want to record programmes at
1
2
3
the same time on a daily or weekly
¶
basis, press the
button once or
4
5
6
EW/ED
twice.
7
8
9
The Function "daily" is not possible
for recording on Saturdays or Sun-
0
SAT
days.
The tape speed (standard or longplay)
¶
can be selected with the
button.
LP
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
