Grundig GV 440 NIC Servicehandbuch Seite 36

2. Connecting and Setting Up
H H
A1 DECODER A2
L L
Switching the Recorder´s Transmitter Off
and On
If your recorder receives many TV stations between the chan-
nels 30 and 40 in the UHF band, you may experience picture
interference when using your recorder. To avoid this, the
recorder´s transmitter can be switched off.
In order for the picture/sound signal of the recorder to be
passed to the TV set, the two units must be connected by
means of a EURO-AV cable.
Improving the picture quality
If wavy lines are visible on the TV screen, the channel tuned
to is already occupied by a TV station.
In this case, proceed as follows:
"
Press the button on the recorder.
On the TV set, search for a channel – in the UHF band be-
tween the channels 30 and 40 + 2 channels – which is not
occupied by a TV station (only snow on the picture screen).
Store the channel found in the memory of the TV set (see the
operating instructions for the TV set).
Remove the aerial cable from the socket – – of the recorder.
II
There should be no cassette in the recorder.
Switch to the test pattern by pressing the J button on the
recorder.
After a few seconds, the recorder will transmit the test pat-
tern.
q
Using the alignment pin supplied, turn the channel selector
(FREQ./MOD.) on the back of the recorder (see illustration)
slightly to the right or left until the test pattern appears on the
screen.
Reconnect the aerial cable to the socket – – of the recorder.
II
"
Complete the adjustment by pressing the button on the
recorder.
Switching the recorder´s transmitter off
Z 8 5 1 8
Press the button, the numbered buttons
O
and the button.
The transmitter of the recorder is now switched off.
»O F F « appears briefly in the display of the recorder.
Switching the recorder´s transmitter on
Z 8 5 1 9
Press the button, the numbered buttons
O
and the button.
The transmitter of the recorder is now switched on.
»O N« appears briefly in the display of the recorder.
2.1 Connecting and Setting Up
Tuning to TV Stations with the Automatic
Tuning System (ATS)
Preparation
Switch the TV set on.
Select the AV programme position for the recorder on the TV
set.
You can now check the settings on the TV screen.
Press these buttons on the You will see this in the display
remote control of the recorder
1. Selecting the ATS function
" ENGLIS 88 88:88
ATS , P R O G START
SEC PAL C +
S A T DATE
2. Selecting the language (of your
location)
a) no b) yes
S A ENGLIS 88 88:88
P R O G START
SEC PAL C +
or
S A T DATE
" "
–GB–SC 88 88:88
ATS , ATS , P R O G START
SEC PAL C +
S A T DATE
3. Selecting the country (location)
a) no b) yes
–GB–SC 88 88:88
P R O G START
S A
SEC PAL C +
S A T DATE
or
for sets with ShowView
Explanations
88:88:88
S T O P All previously stored channel num-
VPS
PDC
bers will be erased.
» ENGLIS « appears in the display of the
recorder as the language.
When you select the "language", the
ATS tuning system searches for and
stores those stations that broadcast in
the respective language.
You can choose from different lan-
88:88:88 guages.
S T O P
VPS
PDC
88:88:88
» GB « appears in the display of the re-
S T O P
VPS
PDC
corder as the country.
When you select the "country", the ATS
tuning function searches for and stores
those stations that broadcast in the res-
pective country.
88:88:88
S T O P
VPS
You can choose from different coun-
PDC
tries.