Inhaltsverzeichnis
Werbung
308
Anhang C: MIDI
MIDI-Datenformat
1. DATA FORMAT
1.1 CHANNEL MESSAGE
Command
8n NOTE OFF
9n NOTE ON
Bn CONTROL CHANGE
Cn PROGRAM CHANGE
1.2 SYSTEM COMMON MESSAGE
Command
F1 MIDI TIME CODE QUARTER
FRAME
1.3 SYSTEM REALTIME MESSAGE
Command
F8 TIMING CLOCK
FE ACTIVE SENSING
FF RESET
1.4 EXCLUSIVE MESSAGE
1.4.1 Real Time System Exclusive
Command
F0 7F dd 06 ... F7 MMC
COMMAND
F0 7F dd 07 ... F7 MMC RESPONSE rx
F0 7F dd 01 ... F7 MIDI TIME CODE rx
1.4.2 System Exclusive Message
1.4.2.1 Bulk Dump
Command
F0 43 0n 7E ... F7 BULK DUMP
DATA
F0 43 2n 7E ... F7 BULK DUMP
REQUEST
The following data types of bulk dump are used on the 01V96.
Data name
'm'
'S'
'L'
'V'
'U'
'C'
'P'
'Q'
'Y'
'G'
'E'
'H'
'R'
'O'
'N'
1.4.2.2 PARAMTER CHANGE
Command
F0 43 1n 3E 0D ... F7 RARAMETER
CHANGE
F0 43 3n 3E 0D ... F7 PARAMETER
REQUEST
F0 43 1n 3E 7F ... F7 PARAMETER
CHANGE
F0 43 3n 3E 7F ... F7 PARAMETER
REQUEST
01V96 Version 2—Bedienungsanleitung
rx/tx
function
rx
Control the internal effects
rx
Control the internal effects
rx/tx
Control parameters
rx/tx
Switch scene memories
rx/tx
function
rx
MTC
rx/tx
function
rx
MIDI clock
rx
Check MIDI cable connections
rx
Clear running status
rx/tx
function
tx
MMC command
MMC response
MTC full message
rx/tx
function
BULK DUMP DATA
rx/tx
BULK DUMP REQUEST
rx/tx
tx/rx
function
tx/rx
Scene Memory & Request
(compressed data)
tx/rx
Setup Memory & Request
tx/rx
User defined MIDI remote &
Request
tx/rx
User defined keys & Request
tx/rx
User assignable layer & Request
tx/rx
Control change table & Request
tx/rx
Program change table & Request
tx/rx
Equalizer library & Request
tx/rx
Compressor library & Request
tx/rx
Gate library & Request
tx/rx
Effect library & Request
tx/rx
Channel library & Request
tx/rx
Input patch library & Request
tx/rx
Output patch library & Request
tx/rx
Plug-in Effect Card Data & Request
rx/tx
function
rx/tx
01V96-specific parameter change
rx/tx
01V96-specific parameter change
rx/tx
General purpose digital mixer
parameter change
rx/tx
General purpose digital mixer
parameter request
The following data types of parameter change are used by the 01V96.
Type (HEX)
1 (01)
2 (02)
3 (03)
4 (04)
16 (10)
17 (11)
18 (12)
19 (13)
20 (14)
32 (20)
33 (21)
34 (22)
* 'tx' indicates that the data can be transmitted from the 01V96, and
'rx' indicates that the data can be received by the 01V96.
2. Format Details
2.1 NOTE OFF
Reception
If [OTHER ECHO] is ON, these message are echoed from MIDI OUT.
If the [Rx CH] matches, these messages are received and used to control effects.
Note off message
STATUS
1000nnnn 8n
Note number
DATA
0nnnnnnn nn
Velocity(ignored)
0vvvvvvv vv
2.2 NOTE ON
Reception
If [OTHER ECHO] is ON, these messages are echoed from MIDI OUT.
If the [Rx CH] matches, these messages are received and used to control effects.
Note on message
STATUS
1001nnnn 9n
Note number
DATA
0nnnnnnn nn
Velocity(1-127:on, 0:off)
0vvvvvvv vv
2.3 CONTROL CHANGE
Reception
If [Control Change ECHO] is ON, these messages are echoed from MIDI OUT.
If [TABLE] is selected, these message are received if [Control Change Rx] is ON,
and will control parameters according to the [Control assign table] settings.
The parameters that can be set are defined in the Control Change Assign Pa-
rameter List.
If [NRPN] is selected, these messages are received if [Control Change Rx] is ON
and the [Rx CH] matches, and will control the parameter that is specified by the
four messages NRPN control number (62h, 63h) and Data Entry control num-
ber (06h, 26h). Parameter settings are defined in the Control Change Assign Pa-
rameter List.
Transmission
If [TABLE] is selected, operating a parameter specified in the [Control assign ta-
ble] will cause these messages to be transmitted if [Control Change Tx] is ON.
The parameters that can be specified are defined in the Control Change Assign
Parameter List.
If [NRPN] is selected, operating a specified parameter will cause data to be
transmitted on the [Tx CH] if [Control Change Tx] is ON, using the four mes-
sages NRPN control number (62h, 63h) and Data Entry control number (06h,
26h). Parameter settings are defined in the Control Change Assign Parameter
List.
This data cannot be transmitted via control change to Studio Manager since
there is no guarantee that the contents of the tables will match. (Parameter
Change messages will always be used.)
tx/rx
function
tx/rx
Edit buffer
tx/rx
Patch data
tx/rx
Setup data
tx/rx
Backup data
tx/rx
Function (recall, store, title, clear)
rx
Function (pair, copy)
rx
Function (effect)
tx/rx
Sort table
tx/rx
Function (attribute, link)
rx
Key remote
tx/rx
Remote meter
tx/rx
Remote time counter
(8n)
(9n)
(Bn)
Werbung
Inhaltsverzeichnis
