Herunterladen Diese Seite drucken

Honeywell 026366.00 Montageanleitung Und Bedienungsanleitung Seite 3

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Mounting and Operation Instructions
Contactless reader, s. m.
Item no. 026366.00 / 026366.10
Mounting / Connection Informations
Attention!
Before opening the reader the device must be de-energized.
The reader is only allowed to be operated with a voltage from 11
to 15 V DC.
The reader can reach a current consumption of up to 450 mA.
The cable cross section
installation manual, calculation examples).
Use a shielded cable when connecting the reader 026366.10 to
a central unit. Connect the shielding to terminal KL1 of the
reader and to the corresponding terminal of the central unit.
Between contactless readers must be a minimum distance
of 3 m in all directions.
Do not install the reader directly on metal as this would
considerably reduce the reading distance.
Avoid direct sun rays.
The reader should not be exposed to plastic decomposing
solvent vapours.
Component diagram item no. 026366.10
KL1 = shield terminal
1
ST2
7
1
ST3
4
Cover contact
Component diagram item no. 026366.00
1
cover contact
8
Attention!
High Voltage
P30704-45-002-00
2008-10-01
must be observed
(e. g. ACS-8
Terminating resistors
only 026366.10
Attention!
High Voltage
D
GB
DIP-Switches 026366.10
Address
DIP-switch
Address
5
4
3
2
1
0
0
0
0
1
1
0
0
0
1
0
2
0
0
0
1
1
3
0
0
1
0
0
4
0
0
1
0
1
5
0
0
1
1
0
6
1
1
1
7
0
0
0
1
8
0
0
0
1
9
0
0
0
1
1
1
1
1
1
31
0 0 0
0
0
32
Connections
026366.10
ST1
signal name
ST16
signal name
1
Clock
1
0V RS485
2
D
2
GND
3
D*
3
+12V DC
4
RS485EN**
4
LED rot
5
LED gelb
6
LED grün
7
Data
** RS485EN may only be used, if the reader is connected to an
ACS-8 via a potential isolation module (see connection
diagrams of ACS-8 and potential isolation module). In all other
cases this cable must not be connected. The guarantee expires
with wrong wiring, as the device might be damaged or
destroyed.
Technical data
Rated operating voltage
Operating voltage range
Interface 026366.10
Interface 026366.00
Current consumption
Protection category
Transmitting frequency
Operation temperature range
environmental class in acc. with VdS
Read distance
Colour case
Colour foil
* Drip-proof, otherwise class II
By using the ID keyfob the read distance is reduced.
**
The device complies with the essential requirements of
the R&TTE 1999/5/EC Directive, if used for its intended
use. The EC-Declaration of Conformity can be
downloaded from our homepage (Service / Download).
Baud rate
DIP-switch
Baud rate
6
0
19200
1
9600
Reader mode
DIP-switch
Reader
mode
8
7
0
0
-
0
1
Clock/Data
0
1
RS 485
1
1
-
In clock/data mode the
DIP-switch 1-6 must be
in position "0".
026366.00
ST16
signal name
1
clock
2
GND
3
+12V DC
4
LED red
5
LED yellow
6
LED green
7
free
8
data
12V DC
11V DC up to 15V DC
clock/data and RS 485
clock/data
400mA + 12mA/LED
IP40
125kHz
-25°C up to +60°C
III*
ca. 25cm**
grey-white (similar to RAL 9002)
light-grey (similar to RAL 7035)
Subject to change
without notice

Werbung

loading

Diese Anleitung auch für:

026366.10