Operation; Switching On/Off - Conrad 84 14 08 Bedienungsanleitung

Controls
Button "A"
• Press briefly: confirms a setting
Activates the illumination for a few seconds
• press for 3 seconds: Time mode: Setting the Time
In the function modes: Reset values
Button "B"
• Press briefly: Selects a function
Changing a value
• press for 3 seconds: Activate scan mode

Switching On/Off

If there is nothing displayed, turn the cyclometer on by briefly pressing any key. If this does not work check the
cyclometer's battery and replace it if necessary.
If no button is pressed, or no movement detected via the radio sensor, the cyclometer turns off automatically
after about 5 minutes in order to save energy.
The radio sensor cannot be turned off. However, it needs less energy so it does not need to be turned off.
Basic Setting
Hold down both buttons of the cyclometer for about 3 seconds, allowing all display elements to appear; now
release the buttons.
IThe value for the wheel perimeter (in millimetre) is flashing on the display.
Change the value using the right button "B"; hold the button down for faster set-
ting. Using the left button "A" takes you to the next digit to the left.
After setting the fourth digit for the wheel perimeter, and confirming with the left
button "A", the distance unit flashes. Choose between "KM" (kilometres) and "M"
(miles), using the right button (B). Confirm the selection, by pressing the left but-
ton (A).
Enter your age. As usual, you set the flashing digit with the right button (B);
change to the next digit using the left button (A).
Enter your weight. As usual, you set the flashing digit with the right button (B);
change to the next digit using the left button (A). If you have set "KM" (kilometres)
as the unit for the distance, use kilograms here. If you have chosen "M" (miles),
enter this value in British pounds.
In the last setting, the right button (B) can be used to set the distance for the serv-
ice interval (e.g. checking tire pressure and suchlike). After covering the set dis-
tance a small wrench icon is displayed.
Press the left button "A" to leave the setting mode and the time of day appears in
the lower display.
12/24 hr Mode + Setting the Time
• Keep pressing the right button "B", until the time appears in the display.
• Hold down the button "A" for about 3 seconds, until "24" (or "12") flashes on the display.
• Select the 12 hr or the 24hr mode, using the right button (B). Press the left button (A) to confirm.
• The hours of the time display start to flash. Set the value using the right button (B); hold the button down for
faster setting. Press the left button (A) to confirm.
• The minutes of the time display start to flash. Set the minutes using the right button (B); hold the button down
for faster setting. Press the left button (A) to confirm.
• The setting mode is exited; the set time appears on the display.
Hold left button (A) down
for 3 seconds

Operation

If the cyclometer is in the normal display mode (which is not the basic setting or the time setting mode), the
following functions can be selected using the right button "B":
To select the 12/24 hr mode and to set the time please see the chapter "12/24 hr
Mode + Setting the Time", see above.
Briefly press the right button "B" to get to the next function.
When "ODO" is shown on the display, the total distance covered since the initial
set-up is displayed.
This data, however, is lost after replacing the batteries.
In order to re-enter the distance, press and hold the left button "A" down for
3 seconds, until the last digit starts flashing. Use the right button "B", to set the val-
ue. Confirm the entry with the left button "A" and move to the next digit.
After entering the last digit, you can return to the normal display by using the left
button "A".
"DST": Here the distance travelled during the day is displayed. It can be reset to
"00000" by pressing and holding down the left button "A" down for 3 seconds.
Briefly press the right button "B", to get to the next function.
"MXS": The bottom display line shows the previous maximum speed. It can be
deleted by pressing and holding the left button "A" down for 3 seconds.
Briefly press the right button "B", to get to the next function.
"AVS": The bottom line of the display shows the average speed over the distance
so far travelled during the day. This is also deleted when resetting the distance for
the day (refer to "DST").
Briefly press the right button "B", to get to the next function.
"TM": The time displayed at the bottom shows the time travelled today. Only the
time during which the cyclometer detected movement is displayed. The time stops
during a standstill (e.g. during a break). It is also deleted when the day's distance
(refer to "DST") is reset.
Briefly press the right button "B", to get to the next function.
The current temperature appears, as next function.
In order to change the temperature unit between "°C" (degree Celsius) and "°F"
(degree Fahrenheit), press and hold the left button "A" down for 3 seconds. The
temperature unit flashes, and you can change it, by briefly pressing the right but-
ton "B". Confirm the selection by briefly pressing the left button "A".
When the temperature is displayed, you can change between the maximum and
minimum temperature by briefly pressing the button. The maximum temperature
is indicated by "H" (see figure on the left), the minimum temperature by "L".
When the maximum and minimum temperature are displayed (see figure on the
left), they can be deleted by pressing and holding the left button "A" down for 3
seconds. Three short dashes appear in the display (e.g. "L - - -") before the cur-
rent temperature is set as the maximum and minimum value.
Briefly press the right button "B", to get to the next function.
"SW": This is the cyclometer's integrated stopwatch. It can be started and paused
by briefly pressing the left button "A".
Hold the left button "A" down for 3 seconds, to reset the stopwatch to "00000".
Briefly press the right button "B", to get to the next function.
"CAL": The cyclometer calculates the calorie consumption from the entered val-
ues for weight and age and the distance covered or time.
Hold the left button "A" down for 3 seconds, to reset the displayed value to
"00000".
Briefly press the right button "B", to get to the next function.
"CAL F": Analogous to the display for the calorie consumption (see above), the fat
"burnt" value is displayed here.
Hold the left button "A" down for 3 seconds, to reset the value to "0".
Briefly press the right button "B", to get to the next function.
"SCAN": The cyclometer automatically switches between displaying the distance
for the day ("DST") and the maximum speed ("MXS"), the average speed ("AVS")
and the time taken for day's distance travelled ("TM").
By pressing the right button "B" you can get back to the start (function "ODO").