Inhaltsverzeichnis - Yamaha AX-892 Bedienungsanleitung

CONTENTS
Supplied accessories .....................................................2
Connections ...................................................................4
Controls and their functions ..........................................10
Remote control .............................................................12
Basic operations ...........................................................14
Troubleshooting ............................................................18
Specifications ...............................................................19
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1.
To assure the finest performance, please read this manual
carefully and keep it in a safe place for future use.
2.
Install this unit in a cool, dry and dust-free area. Do not place it in
direct sunlight or near sources of heat (e.g., a stove, etc.). Make
sure that it is well ventilated and not exposed to rain or moisture
and that it is on a flat, stable surface, free from vibration.
3.
Never open the cabinet. If something drops into the unit, contact
your dealer.
4.
When moving the unit, first disconnect the AC power plug and the
cables which are connected to other equipment. Never pull the
cables or use excessive force on switches or controls.
5
. The openings on the cabinet assure proper ventilation of the unit.
If these openings are obstructed, the temperature inside the
cabinet will rise rapidly, damaging the unit or causing a fire. Avoid
blocking the ventilation openings and make sure that the unit is
well ventilated. Allow at least 30 cm (12 in) of space above the
unit and 20 cm (8 in) of space on the sides and rear.
Always set the VOLUME control to " ∞ " before playing the source.
6.
Increase the volume gradually to a desired level after the source
has started playing.
7.
Use a clean, dry cloth to clean the unit. Do not use chemical
solvents which might damage the finish.
8.
Be sure to read the "TROUBLESHOOTING" section before
deciding that the unit is faulty.
9.
When not planning to use this unit for long periods of time (e.g.,
vacation, etc.), disconnect the AC power plug from the electrical
outlet.
10.
To prevent damage from lightning, disconnect the AC power plug
and antenna cable when there is an electrical storm.
11.
Make sure that the unit is always properly grounded and
polarized.
12.
Do not connect audio equipment to the AC outlet on the rear panel
if the equipment requires more power than the outlet is rated to
provide.
Thank you for selecting this YAMAHA stereo amplifier.
FEATURES
85W + 85W (8Ω) RMS Output Power,
AX-492
0.019% THD, 20-20,000 Hz
100W + 100W (8Ω) RMS Output Power,
AX-592
0.015% THD, 20-20,000 Hz
115W + 115W (8Ω) RMS Output Power,
AX-892
0.015% THD, 20-20,000 Hz
High Dynamic Power, Low Impedance Drive Capability
Continuously Variable Loudness Control
CD DIRECT AMP switch: used to reproduce the purest
CD sound
PURE DIRECT switch: used to reproduce the purest
source sound
SUBSONIC FILTER switch; used to eliminate undesirable
ultra-low-frequency signals ( AX-592 and AX-892 only )
PRE OUT/MAIN IN terminals; useful for connecting an
equalizer, sound processor, etc. ( AX-592 and AX-892
only )
Remote control capability
13.
Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit must be set
for your local main voltage
outlet.
Voltages are 110/120/220/240 V AC, 60/50 Hz.
WARNING
To reduce the risk of fire or electric shock, do not expose the unit to
rain or moisture.
IMPORTANT
The serial number is located on the rear panel.
Please record the serial number of this unit in the space below.
Serial No.:
Keep this Owner's Manual in a safe place for future use.
Note
The unit is not disconnected from the AC power source as long as it
is connected to the electrical outlet, even if the unit itself is turned
off.
For UK customers
If the electrical outlets in the home are not suitable for the plug
which is supplied with this unit, cut off the plug and attach an
appropriate 3-pin plug.
Note
The removed plug must be destroyed, as a plug with exposed wires
is hazardous if inserted into a live electrical outlet.
IMPORTANT
The wires in the mains lead are colored as follows:
Blue: Neutral
Brown: Live
As the colors of the wires in the mains lead of this apparatus may
not correspond with the colored markings identifying the terminals in
your plug, proceed as follows:
The wire which is colored BLUE must be connected to the terminal
which is marked with the letter N or colored BLACK. The wire
which is colored BROWN must be connected to the terminal which
is marked with the letter L or colored RED. Make sure that neither
core is connected to the ground terminal of the 3-pin plug.
before plugging into the electrical
3