Yamaha NS-P610 Bedienungsanleitung Seite 3

Thank you for selecting this YAMAHA NS-P610 Speaker Package.
CAUTION: Read this before operating your unit.
●
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
●
Install the speakers in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration, dust,
moisture and cold. Avoid sources of humming (transformers,
motors). To prevent fire or electric shock, do not expose the
speakers to rain or water.
●
To prevent the enclosure from warping or discoloring, do not
place the speakers where they will be exposed to direct sunlight
or excessive humidity.
●
Do not place the following objects on top of the speakers:
Other components, as they might cause damage and/or
●
discoloration on the surface of the speakers.
● Burning objects (i.e. candles), as they might cause fire,
damage to the speakers and/or personal injury.
● Containers with liquid in them, as they might cause electric
shock to the user and/or damage to the speakers.
●
Do not place the speakers where they are liable to be knocked
over or struck by falling objects. Stable placement will also
ensure better sound performance.
●
Placing the speakers on the same shelf or rack as the turntable
can result in feedback.
●
Secure placement or installation is the owner's responsibility.
YAMAHA shall not be liable for any accident caused by improper
placement or installation of speakers.
●
Any time you note distortion, reduce the volume control on your
amplifier to a lower setting. Never allow your amplifier to be
driven into "clipping". Otherwise the speakers may be damaged.
●
When using an amplifier with a rated output power higher than
the nominal input power of the speakers, care should be taken
never to exceed the speakers' maximum input.
●
Do not attempt to clean the speakers with chemical solvents as
this might damage the finish. Use a clean, dry cloth.
●
Do not attempt to modify or fix the speakers. Contact qualified
YAMAHA service personnel when any service is needed. The
cabinet should never be opened for any reasons.
●
Be sure to read the "TROUBLESHOOTING" section regarding
common operating errors before concluding that the speakers
are faulty.
For YST-SW45 only
●
Do not operate this unit upside down. It may overheat, possibly
causing damage.
●
Do not use force on switches, controls or connection wires.
When moving this unit, first disconnect the power plug and the
wires connected to other equipments. Never pull the wires
themselves.
●
Since this unit has a built-in power amplifier, heat will radiate
from the rear panel. Place the unit apart from the walls, allowing
20 cm above, behind and on both sides of the unit to prevent fire
or damage. Furthermore, do not position with the rear panel
facing down on the floor or other surfaces.
●
To avoid condensation inside this unit, do not expose this unit to
sudden temperature changes from cold to hot, or do not place
this unit in an environment with high humidity (i.e. a room with a
humidifier). Condensation may cause an electric shock, fire,
and/or damage to this unit.
●
Do not cover the rear panel of this unit with a newspaper, a
tablecloth, a curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause fire, damage
to this unit and/or personal injury.
●
Do not plug in this unit to a wall outlet until all connections are
completed.
●
The voltage to be used must be the same as that specified on
the rear panel. Using this unit with a higher voltage than
specified is dangerous and may cause fire, damage to this unit,
and/or personal injury. YAMAHA will not be held responsible for
any damage resulting from use of this unit with a voltage other
than specified.
●
To prevent lightning damage, disconnect the AC power plug
when there is an electric storm.
●
Super-bass frequencies reproduced by this unit may cause a
turntable to generate a howling sound. In such a case, move this
unit away from the turntable.
●
This unit may be damaged if certain sounds are continuously
outputted at high volume level. For example, if 20 Hz–50 Hz sine
waves from a test disc, bass sounds from electronic instruments,
etc. are continuously outputted, or when the stylus of a turntable
touches the surface of a disc, reduce the volume level to prevent
this unit from being damaged.
●
If you hear distorted noise (i.e. unnatural, intermittent "rapping" or
"hammering" sounds) coming from this unit, reduce the volume
level. Extremely loud playing of a movie soundtrack's low
frequency, bass-heavy sounds or similarly loud popular music
passages can damage this speaker system.
●
Vibration generated by super-bass frequencies may distort
images on a TV. In such a case, move this unit away from the TV
set.
●
When disconnecting the power cord from the wall outlet, grasp
the plug; do not pull the cord.
●
When not planning to use this unit for a long period (i.e. vacation,
etc.), disconnect the AC power plug from the wall outlet.
VOLTAGE SELECTOR (China and general models only)
The VOLTAGE SELECTOR on the rear panel of this unit must be
set for your local main voltage BEFORE plugging into the AC
main supply. Voltages are 110-120/220-240 V AC, 50/60 Hz.
Standby mode
When this unit is turned off by pressing the STANDBY/ON button
on the front panel, it consumes a small amount of power. This
state is called the standby mode. This unit's power supply is
completely cut off from the AC line only when the POWER switch
on the rear panel is set in the OFF position or the AC power cord
is disconnected.
These speakers feature a magnetically shielded design, but
there is still a chance that placing them too close to a TV set
might impair picture color. Should this happen, move the
speakers away from the TV set.
1
E-