Herunterladen Inhalt Inhalt Diese Seite drucken

CYBEX Onyx Benutzerhandbuch Seite 19

Vorschau ausblenden Andere Handbücher für Onyx:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
d) To release the fasteners squeeze the grooves on left and right side of the central
harness buckle.
e) Adjust the length of the crotch strap with the corresponding slider.
warning: alwaYs usE ThE CrOTCh sTrap in COmBinaTiOn
wiTh ThE waisT BElT.
12. ADjUSTING THE HARNESS SYSTEM FOR NEWBORNS
a) Release the loops at the end of the shoulder straps from the triangle in the belt
system, situated at the bottom of the backrest under the seat cover.
b) completely pull the shoulder straps out of the holes in the backrest.
c) feed the shoulder straps through the two bottom holes. make sure to feed the
straps back through the holes in the backrest mechanism and re-attach them
to the triangle.
d) To adjust the length of the shoulder straps to newborns please attach the inner
loop of the shoulder strap ends to the triangular ring. switch back to the upper
holes as soon as the shoulder straps do no longer fit over the child´s shoulders.
13. REMOVING THE HEADHUGGER AND SHOULDER PADS (TOPAz ONLY)
Remove the headhugger as soon as the headhugger does no longer fit over the
child´s shoulders.
a) Remove the velcros of the headhugger on the top leh and right side on the
back of the seat cover.
b) Release the loops at the end of the shoulder straps from the triangle in the belt
system, situated at the bottom of the backrest under the seat cover.
c) completely pull the shoulder straps out of the holes in the backrest.
d) Pull the shoulder straps through the shoulder pads and the headhugger. make
sure to feed the straps back through the holes in the backrest mechanism and
attach them to the triangle. You can use the headhugger and the shoulder
pads separately.
14. REMOVING THE SEATCOVER
a) Slightly fold the stroller to reduce tension.
b) Remove the canopy from the stroller, if attached.
c) Take the seat cover's hooks (3) off the frame on left and right side
d) Open the press buttons (4) of the straps connected to the seat side panels and
the basket rear tube.
e) Open the flaps (5) which are fixed with velcro over the tubes, one on each side.
f) feed the strap with the slider (6) of the central harness buckle through the hole
in the seat fabric.
g) feed the loops on the end of the shoulder straps through the triangle in the
backrest (7).
h) feed the shoulder straps through the holes in the seat fabric (8).
i) Open the press buttons which are on the left and the right side from the seat on
the bottom from the fabric.
j) Pull the seat cover over the belt shifting button on the seat.
k) Slide the fabrics from the seat base tubes.
l) Reverse this procedure to refit the seat cover and the harness. make sure that
the seat tubes slide back into the pockets inside the seat cover.
15. RECLINING THE LEG REST
a) Press the leg rest on both front edges and push down.
b) Simply lift the leg rest to put it back to the starting position.
16. RECLINING THE SEAT
a) Pull the recline lever at the back of the seat in order to recline the backrest to
the 4 different positions.
b) To raise lift the complete backrest up to required position.
17. CARRYING THE STROLLER
Pull the flexible carring handle on right rear tube and lift the stroller.
18. ATTACHING THE RAINCOVER (OPTIONAL)
a) Extend the rain cover over the stroller like shown in the image
b) To fit the rain cover fasten the velcro strips around the frame at the top and
bottom on both sides of the buggy.
19. WARRANTY
The following warranty applies solely in the country where this product was initially
sold by a retailer to a customer. The warranty covers all manufacturing and
material defects, existing and appearing, at the date of purchase or appearing
within a term of two (2) years from the date of purchase from the retailer who
initially sold the product to a consumer (manufacturer's warranty). In the event
that a manufacturing or material defect should appear, we will – at our own
discretion – either repair the product free of charge or replace it with a new
product. To obtain such warranty it is required to take or ship the product to the
retailer, who initially sold this product to a customer and to submit an original proof
of purchase (sales receipt or invoice) that contains the date of purchase, the
name of the retailer and the type designation of this product. This warranty shall not
apply in the event that this product is taken or shipped to the manufacturer or any
other person other than the retailer who initially sold this product to a consumer.
please check the product with respect to completeness and manufacturing or
material defects immediately at the date of purchase or, in the event that the
product was purchased in distance selling, immediately after receipt. in case of a
defect stop using the product and take or ship it immediately to the retailer who
initially sold it. in a warranty case the product has to be returned in a clean and
complete condition. prior to contacting the retailer, please read this instruction
manual carefully. This warranty does not cover any damages caused by misuse,
environmental influence (water, fire, road accidents etc.) or normal wear and
tear. it does solely apply in the event that the use of the product was always in
compliance with the operating instructions, if any and all modifications and
services were performed by authorized persons and if original components and
11

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Topaz

Inhaltsverzeichnis