Inhaltsverzeichnis
Werbung
MIDI-Datenformat
1. DATA FORMAT
1.1 CHANNEL MESSAGE
Command
rx/tx
8n NOTE OFF
rx
9n NOTE ON
rx
Bn CONTROL CHANGE
rx/tx
Cn PROGRAM CHANGE
rx/tx
1.2 SYSTEM COMMON MESSAGE
Command
rx/tx
F1 MIDI TIME CODE QUARTER
rx
FRAME
1.3 SYSTEM REALTIME MESSAGE
Command
rx/tx
F8 TIMING CLOCK
rx
FE ACTIVE SENSING
rx
FF RESET
rx
1.4 EXCLUSIVE MESSAGE
1.4.1 Real Time System Exclusive
Command
rx/tx
F0 7F dd 06 ... F7 MMC
tx
COMMAND
F0 7F dd 07 ... F7 MMC RESPONSE rx
F0 7F dd 01 ... F7 MIDI TIME CODE rx
1.4.2 System Exclusive Message
1.4.2.1 Bulk Dump
Command
rx/tx
F0 43 0n 7E ... F7 BULK DUMP
DATA
rx/tx
F0 43 2n 7E ... F7 BULK DUMP
REQUEST
rx/tx
The following data types of bulk dump are used on the 01V96i.
Data name
tx/rx
'm'
tx/rx
'S'
tx/rx
'L'
tx/rx
'V'
tx/rx
'U'
tx/rx
'C'
tx/rx
'P'
tx/rx
'Q'
tx/rx
'Y'
tx/rx
'G'
tx/rx
'E'
tx/rx
'H'
tx/rx
'R'
tx/rx
'O'
tx/rx
'N'
tx/rx
1.4.2.2 PARAMTER CHANGE
Command
rx/tx
F0 43 1n 3E 0D ... F7 RARAMETER
rx/tx
CHANGE
F0 43 3n 3E 0D ... F7 PARAMETER
rx/tx
REQUEST
F0 43 1n 3E 7F ... F7 PARAMETER
rx/tx
CHANGE
F0 43 3n 3E 7F ... F7 PARAMETER
rx/tx
REQUEST
function
Control the internal effects
Control the internal effects
Control parameters
Switch scene memories
function
MTC
function
MIDI clock
Check MIDI cable connections
Clear running status
function
MMC command
MMC response
MTC full message
function
BULK DUMP DATA
BULK DUMP REQUEST
function
Scene Memory & Request
(compressed data)
Setup Memory & Request
User defined MIDI remote &
Request
User defined keys & Request
User assignable layer & Request
Control change table & Request
Program change table & Request
Equalizer library & Request
Compressor library & Request
Gate library & Request
Effect library & Request
Channel library & Request
Input patch library & Request
Output patch library & Request
Plug-in Effect Card Data & Request
function
01V96i-specific parameter change
01V96i-specific parameter change
General purpose digital mixer
parameter change
General purpose digital mixer
parameter request
MIDI-Datenformat
The following data types of parameter change are used by the 01V96i.
Type (HEX)
tx/rx
1 (01)
tx/rx
2 (02)
tx/rx
3 (03)
tx/rx
4 (04)
tx/rx
16 (10)
tx/rx
17 (11)
rx
18 (12)
rx
19 (13)
tx/rx
20 (14)
tx/rx
32 (20)
rx
33 (21)
tx/rx
34 (22)
tx/rx
* 'tx' indicates that the data can be transmitted from the 01V96i, and
'rx' indicates that the data can be received by the 01V96i.
2. Format Details
2.1 NOTE OFF
Reception
If [OTHER ECHO] is ON, these message are echoed from MIDI OUT.
If the [Rx CH] matches, these messages are received and used to control effects.
Note off message
STATUS
1000nnnn 8n
Note number
DATA
0nnnnnnn nn
Velocity(ignored)
0vvvvvvv vv
2.2 NOTE ON
Reception
If [OTHER ECHO] is ON, these messages are echoed from MIDI OUT.
If the [Rx CH] matches, these messages are received and used to control effects.
Note on message
STATUS
1001nnnn 9n
Note number
DATA
0nnnnnnn nn
Velocity(1-127:on, 0:off)
0vvvvvvv vv
2.3 CONTROL CHANGE
Reception
If [Control Change ECHO] is ON, these messages are echoed from MIDI OUT.
If [TABLE] is selected, these message are received if [Control Change Rx] is ON,
and will control parameters according to the [Control assign table] settings.
The parameters that can be set are defined in the Control Change Assign Pa-
rameter List.
If [NRPN] is selected, these messages are received if [Control Change Rx] is ON
and the [Rx CH] matches, and will control the parameter that is specified by the
four messages NRPN control number (62h, 63h) and Data Entry control num-
ber (06h, 26h). Parameter settings are defined in the Control Change Assign Pa-
rameter List.
Transmission
If [TABLE] is selected, operating a parameter specified in the [Control assign
table] will cause these messages to be transmitted if [Control Change Tx] is ON.
The parameters that can be specified are defined in the Control Change Assign
Parameter List.
If [NRPN] is selected, operating a specified parameter will cause data to be
transmitted on the [Tx CH] if [Control Change Tx] is ON, using the four mes-
sages NRPN control number (62h, 63h) and Data Entry control number (06h,
26h). Parameter settings are defined in the Control Change Assign Parameter
List.
This data cannot be transmitted via control change to Studio Manager since
there is no guarantee that the contents of the tables will match. (Parameter
Change messages will always be used.)
173
function
Edit buffer
Patch data
Setup data
Backup data
Function (recall, store, title, clear)
Function (pair, copy)
Function (effect)
Sort table
Function (attribute, link)
Key remote
Remote meter
Remote time counter
(8n)
(9n)
(Bn)
01V96i—Referenzhandbuch
Werbung
Inhaltsverzeichnis
