Installing This Unit - Yamaha YSP-1100 Bedienungsanleitung

YSP-1100
This quick reference guide explains steps to connect a TV and a DVD player to this unit and achieve the
surround sound effects in a quick, easy manner. For detailed operation, refer to the Owner's Manual.

Installing this unit

Decide where to install this unit.
Install this unit where there are no objects such as furniture obstructing the path of sound beams. Otherwise, the desired surround
sound effects may not be achieved. You may install this unit in parallel with the wall or in the corner.
Install this unit in the exact center of the wall when it is
measured from the left and right corners.
An object, such as furniture
Install this unit either above or under your TV.
Please read the following for reference. For further information on installation, see pages 11 and 13 in the Owner's Manual.
Make sure you use the supplied fasteners to prevent an accidental fall of this unit (see page 14 in the Owner's Manual).
When installing this unit above your TV, place it on
the top panel of a commercially available rack as
shown below.
Make sure that the top panel of the rack is wide and
stable enough to support the weight of this unit.
Printed in Malaysia WH90290
English
QUICK REFERENCE GUIDE
Install this unit in the corner at a 40˚ to 50˚ angle from
the adjacent walls.
An object, such as furniture
40˚ to 50˚
When installing this unit under your TV, place it in a
TV cabinet as shown below.
Make sure that the cabinet is large enough to allow
adequate ventilation space around this unit.
To enjoy better surround effects, place this unit
on the upper shelf to keep it away from the floor.
Connecting external components to this unit
Connect external component such as a TV or DVD player to this unit.
Connect your TV or DVD player to this unit using appropriate cables as shown below. Connecting a subwoofer enhances bass sound for listening enjoyment.
For further information on connecting other components, see pages 15 to 22 in the Owner's Manual.
DVD player
TV
Coaxial Video Component
digital output video
output output
Optical Analog Video
digital audio input
output output
R L
1 2a 2b
3
4 5
COMPONENT COMPONENT
DVD AUX TV/STB
COAXIAL OPTICAL TV/STB VCR VCR DVD/AUX STB
RS- 232 C REMOTE IN DIGITAL IN AUDIO IN SUBWOOFER VIDEO IN
Setting up the listening environment automatically
Connect the optimizer microphone to this unit.
You can automatically adjust the various channel settings that best match your listening environment using the supplied optimizer microphone. Follow the procedure below to connect the optimizer microphone to this unit and place it in a proper location.
Connect the optimizer microphone to the OPTIMIZER MIC jack on the left side of this unit.
Optimizer microphone (supplied)
Set the optimizer microphone at your normal listening position. Use the supplied cardboard microphone stand or a tripod to place the optimizer microphone at the
same height as your ears would be when you are seated.
Optimizer
microphone
Within 1 m (3.3 ft)
More than
upper or lower
1.8 m (6.0 ft)
from the center
Cardboard
microphone Sofa
stand
Cables used for connections
Connect cables in the following order. For the connection 2, use
either (a) or (b). If your DVD player has component video output
jacks, we suggest using the cable (b).
1 Digital audio pin cable (supplied)
2a Video pin cable
Component
video
2b Component video pin cable
input
3 Optical cable (supplied)
4 Audio pin cable (supplied)
5 Video pin cable (supplied)
6 Component video pin cable
(in case of a component connection)
6
7 Subwoofer pin cable
(in case you connect a subwoofer)
8 Power supply cable (supplied)
Subwoofer
7
Monaural
input
COMPONENT
This unit
VIDEO OUT
Cardboard microphone stand (supplied)
Assemble the cardboard microphone stand and place the
optimizer microphone on the top of the stand.
Place the optimizer microphone on the extended center
line of this unit and 1.8 m (6.0 ft) or more away from it.
Also, make sure place the optimizer microphone within
1 m (3.3 ft) upper or lower from the center height of this
unit.
If you have set the optimizer microphone,
Center line
Optimizer
microphone
follow the steps on the backside to start
the AUTO SETUP procedure.
CAUTION
・Do not plug the power
supply cable into a wall
outlet until all connections
are complete.
・Unplug the power supply
cable before changing
connections, moving or
cleaning this unit.
y
If a subwoofer is connected to this unit, turn on the
power of your subwoofer and then carry out the
AUTO SETUP procedure (see the backside) or
select "SWFR" for "BASS OUT" in "SUBWOOFER
SET" (see page 67 in the Owner's Manual).
8
To the AC
outlet
Continued
on the back
C2006
All rights reserved.