Herunterladen Inhalt Inhalt Diese Seite drucken

Installing And Connecting The Speaker; Network - Monacor WALL-05DT Bedienungsanleitung

Aktiver lautsprecher für dante-netzwerke
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

4 Installing and Connecting the Speaker

The speaker is designed for being installed at a wall, but it can also
be set up on its own .
To install the speaker:
1) Remove the plastic support (4) from the metal bracket (3) . Then
use two screws to fasten the support to the desired location (e . g .
wall or ceiling) .
2) Fasten the metal bracket (3) to the plastic support, using the two
recessed head screws of the bracket . Use the holes in the metal
bracket which are most suitable for the desired speaker alignment .
3) Use the screws (2) to fasten the speaker (1) to the metal bracket .
Align the speaker to the desired sound zone before fastening the
screws .

4.1 Network

To configure the signal processor and to feed in audio signals via a
Dante network, connect the jack IN / PoE (5) to an individual comput-
er, a local computer network or (via a router, for example) to a large
computer network . For correct configuration, knowledge in network
technology is indispensable . The speaker can be supplied with power
via the same connection jack if the jack is connected to a network
element providing "Power over Ethernet" (e . g . PoE switch) .
For integration into a Dante network, the speaker must at least
be connected to a Fast Ethernet switch (100 Mbits / s Ethernet) .
Even if the same connection jack of WALL-05DT is used for DSP con-
trol and for feeding in Dante signals, it is internally considered as two
separate Ethernet interfaces with different IP addresses .
Note: When the IP addresses in the local network are set manually, do not assign
the same address to both interfaces!
The DSP interface of WALL-05DT is preset to automatic reception of
an IP address . If a DHCP server is available in the network connected,
the speaker will receive its address from the server . If an ordinary
Ethernet switch is used to connect the speaker to a computer and the
computer has also been set to automatic reception of an address and
if no DHCP server is available, the units will assign an address in the
range 169 .254 .0 .0 – 169 .254 .255 .255 to each other . This may take a
few minutes (depending on the computer system used) . To accelerate
connection without a DHCP server, assign an address in this range to
the computer and set the subnet mask to 255 .255 .0 .0 .
The network settings of the DSP interface can easily be changed
via the menu of the control program . In this menu, it is also possible
to assign a fixed IP address to the speaker (
Note: If the DSP of WALL-05DT is to be configured in large networks by means
of the control program, higher data volumes (e . g . when multiple Dante transmit
channels have been set as multicast flows) may lead to a failure of the control
connection . In this case, it may be necessary to connect a switch ahead of
WALL-05DT which supports "IGMP Snooping" (IGMP = Internet Group Manage-
ment Protocol) . The switch can be configured to reduce the load on WALL-05DT
so that the switch will only route multicast data to WALL-05DT if the speaker
has requested these data .
The Dante interface of the speaker is also preset to automatic address
assignment; configuration via the program "Dante Controller" is
possible . For installation of this program please refer to chapter 5 .
The jack LINK (6) can be used for routing the network connection, e . g .
directly to an additional WALL-05DT . The PoE power supply, however,
is not routed via this jack .
 chapter 7 .11) .
35

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis