Electrical Connection; Cleaning, Maintenance And Storage - Parkside IAN 292195 Bedienungs- Und Sicherheitshinweise

9. Electrical connection

The electrical motor installed is connected and ready
for operation. The connection complies with the appli-
cable VDE and DIN provisions.
The customer's mains connection as well as the exten-
sion cable used must also comply with these regula-
tions.
Important information
In the event of an overloading the motor will switch itself off.
After a cool-down period (time varies) the motor can be
switched back on again.
Damaged electrical connection cable
The insulation on electrical connection cables is often dam-
aged.
This may have the following causes:
• Passage points, where connection cables are passed
through windows or doors.
• Kinks where the connection cable has been improperly
fastened or routed.
Places where the connection cables have been cut due
•
to being driven over.
• Insulation damage due to being ripped out of the wall
outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be
used and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage regu-
larly. Make sure that the connection cable does not hang on
the power network during the inspection.
Electrical connection cables must comply with the applica-
ble VDE and DIN provisions. Only use connection cables
with the marking „H05VV-F".
The printing of the type designation on the connection
cable is mandatory.
AC motor
• The mains voltage must be 220 - 240 V~ 50 Hz.
• Extension cables up to 25 m long must have a cross-
section of 1.5 mm .
2
Connections and repairs of electrical equipment may only
be carried out by an electrician.
Please provide the following information in the event of any
enquiries:
• Type of current for the motor
• Machine data - type plate
Machine data - type plate
•
10. Cleaning, maintenance, and storage
m Important!
Pull out the power plug before doing any cleaning and
maintenance work on the equipment. Risk of injury from
electric shock!
m Important!
Wait until the equipment has cooled down completely! Risk
of burns!
12 GB/IE/NI
m Important!
Always depressurize the equipment before carrying out any
cleaning and maintenance work! Risk of injury!
10.1 Cleaning
• Keep the equipment free of dirt and dust as far as pos-
sible. Wipe the equipment with a clean cloth or blow it
down with compressed air at low pressure.
• We recommend that you clean the equipment immedi-
ately after you use it.
Clean the equipment regularly with a damp cloth and
•
some soft soap. Do not use cleaningagents or solvents;
these may be aggressive to the plastic parts in the
equipment. Ensure that no water can get into the interior
of the equipment.
• You must disconnect the hose and any spraying tools
from the compressor before cleaning. Do not clean the
compressor with water, solvents or the like.
10.2 Maintenance work on the pressure vessel (Fig. 1)
m Important! To ensure a long service life of the pressure
vessel (8), drain off the condensed water by opening the
drain valve (10) each time after using. Release the vessel
pressure first (see 10.7.1). Open the drain screw by turning
counter-clockwise (looking at the screw from the bottom
of the compressor) so that all the condensed water can run
out of the pressure vessel. Then close the drain screw again
(turn it clockwise). Check the pressure vessel for signs of
rust and damage each time before using. Do not use the
compressor with a damaged or rusty pressure vessel. If you
discover any damage, then please contact the customer
service workshop.
m Important!
The condensed water from the pressure vessel will
contain residual oil. Dispose of the condensed water
in an environmentally compatible manner at a suita-
ble collection point.
10.3 Safety valve (Fig. 3)
The safety valve (19) has been set for the highest permitted
pressure of the pressure vessel. It is prohibited to adjust the
safety valve or remove its seal. Actuate the safety valve
from time to time to ensure that it works when required. Pull
the ring with sufficient force until you can hear the com-
pressed air being released. Then release the ring again.
10.4 Checking the oil level at regular intervals (Fig. 11)
Place the compressor on a level and straight surface. The oil
level must be between the MAX and MIN marks on the oil
level window (18).
Oil change: we recommend SAE 15W 40 or equivalent.
The original oil filling must be changed after 100 hours in
operation; thereafter the oil must be drained and replaced
with new oil after every 500 hours in operation.
10.5 Changing the oil (Fig. 3,10)
Switch off the engine and pull the mains plug out of the
socket. Remove the oil sealing plug (16). After releasing any
air pressure you can unscrew the oil drain plug (12) from the
compressor pump (13).