Installation - Bestway 56401 Benutzerhandbuch

Structure:
Before assembling your pool, please take a few minutes to check all the parts and become familar
with their position.
Size: 2.21 m x 1.50 m x 43 cm (87'' x 59'' x 17'')
D
C
A
A
I
B
D
C
J
F K
M
Size: 2.59 m x 1.70 m x 61 cm (102'' x 67'' x 24'')
A
B
A
I
D
B
J
C
A
K
F
E
M
Size: 4.00 m x 2.11 m x 81 cm (157'' x 83'' x 32'')
A
A
C
D
CHOOSE THE CORRECT LOCATION
IMPORTANT: The pool must be set up on a completely flat and level surface. Please do not install
the pool if the surface is inclined or sloped.
Correct conditions to set up the pool:
• The selected location has to be capable of uniformly supporting the weight for the entire time the
pool is installed, moreover the location must be flat and must be cleared of all objects and debris
including stones and twigs.
• We recommend positioning the pool away from any objects kids could use to climb into the pool.
NOTE: Position the pool near an adequate drainage system to deal with overflow or to discharge
the pool.
Incorrect conditions to set up the pool:
• On uneven ground the pool may collapse causing serious personal injury and/or damage to
personal property and will void the warranty and prevent any service claims.
• Sand should not be used to create a level base; the ground must be dug out if necessary.
• Directly under overhead power lines or trees. Be sure the location does not contain underground
utility pipes, lines or cables of any kind.
• Do not set up the pool on driveways, decks, platforms, gravel or asphalt surfaces. The selected
location should be firm enough to withstand the pressure of the water; mud, sand, soft / loose soil
or tar are not suitable.
• Grass or other vegetation under the pool will die and may cause odors and slime to develop,
therefore we recommend removing all grass from the selected pool location.
• Avoid areas prone to aggressive plant and weed species that may grow through the ground cloth
or liner.
NOTE: Check with your local city council for by-laws relating to fencing, barriers, lighting and safety
requirements and ensure you comply with all laws.
NOTE: If have a filter pump, refer to the pump's manual for instructions.
NOTE: The ladder must match the pool size and should to be used only for entering and exiting
the pool. It is forbidden to exceed the permitted payload of the ladder. Check regularly if the ladder
is properly assembled.

Installation

Fig. 1 Fig. 2
Fig. 5
Fig. 6
L
J
K
F
S-S-004372/21.0x28.5cm/(小矩形支架水池说明书E版) JS-YF-2016-B-02621/英
Size: 2.39 m x 1.50 m x 58 cm (94'' x 59'' x 23'')
B
A
B
D
I
C
A
J
K
E
F
M
Size: 3.00 m x 2.01 m x 66 cm (118'' x 79'' x 26'')
A
D
B
C
A
A
I B
C
D A
G
H
F
M
C
A
B
A
B
I
A
A
G
H
N
F
M
Fig. 3
Fig. 4
Fig. 8
Fig. 7
F/G
H
G
E
Assembly of the Frame pool can be completed without tools.
NOTE: It is important to assemble pool in the order shown below. Install your pools according to the
above illustrations.
1. Lay out all parts and check that you have the correct quantities as listed in the parts guide. If
you are missing any part do not assemble the pool, contact our Customer Service Department
for assistance.
NOTE: Vertical pool legs are packaged inside the top rails.
D
2. If pool was purchased with a ground cloth, spread carefully at the desired location. This pool
C
may have been purchased with a Bestway Filter Pump, if a pump is to be used (recommended
B
and also available separately) the pool should be located within distance of a power outlet.
3. Place the Leg Bands (L) on the ground (See Fig. 1). There are different lengths of Leg bands (L),
please ensure you have used the correct sizes at the correct locations.
4. Spread out the pool and put it on the Leg Bands (L). Make sure it is right side up (See Fig. 2).
Let it sit exposed to direct sunlight for 1 hour or more so the pool is more flexible during set up.
5. Turn the pool so the drain valve is near the area where your plan to drain the water and pump
valves are facing the outlet for the optional filter pump.
ATTENTION: Do not drag the pool on the ground in order to avoid damaging the linear on sharp
objects. Bestway Inflatables will not be responsible for damage caused to the pool due to
C
mishandling or failure to follow these instructions.
D
J
6. Insert all of the top rails into the pole sleeves on the top of the pool (See Fig. 3). The
A
combinations for top rails are different for different sizes pools, see the Structure Section for
K
detail.
7. At the middle opening of each sleeve, insert the two ends of the top rails into the Connector (I).
(See Fig. 4)
NOTE: At each Connector ensure both top rails are properly inserted.
N
8. At the corners, insert the top rails into the Corner Seats (J). Insert the Connection Pins (K) into
the pre-drilled holes locking the top rails into position.(See Fig. 5)
9. Insert the Vertical Pool Legs (F) into the bottom of the Corner Seats (J). (See Fig. 5)
10. On the sides of the rectangle, insert the T Support (E), Vertical Pool Legs (F) or the Y-Vertical
Pool Legs (G,H) into the vertical holes of the Connectors (I). (See Fig. 6, See Fig. 8)
D
11. Connect the Side Support Legs (H) to the Y-Vertical Pool Legs (G). Ensure the spring-loaded
J
pins lock into the pre-drilled holes. (See Fig. 6)
12. On each corresponding Pool Leg located on the sides of the rectangle, put the Pool Legs (E, F or G)
K
through the loops of the Leg Bands (L). This will keep both corresponding pool legs locked in
position. (See Fig. 6, See Fig. 8)
13. Attach all Footings (M&N) to the bottom of the Vertical Pool Legs (F) and the Side Support
Legs (H). (See Fig. 7)
14. Test the Frame to ensure all connections are secure before filling with water.
15. Insert the blue stopper plug into the inlet and outlet on the inside wall of the pool.
16. Ensure drain valve is firmly closed.
17. Put 1'' to 2'' water in the pool to cover the floor. Once pool floor is slightly covered, gently
smooth out all wrinkles. Start in the center of the pool and work your way clockwise to the
outside.
FILLING POOL WITH WATER
ATTENTION: Do not leave pool unattended while filling with water
1. Fill pool to drain valve.
STOP
2. Turn water off. Check that the water is not collecting on any side to ensure the pool is level. If
pool is not level, drain water and re-level ground by digging out (See Fig. 10). Never attempt to
move the pool with water in it, serious personal injury or damage to the pool may result.
NOTE: Your pool may contain a great deal of pressure. If your pool has any bulge or uneven
side then the pool is not level, the sides may burst and the water may discharge suddenly
causing serious personal injury and/or damage to property.
3. If level, fill pool to lowest pump valve.
STOP
4. Turn water off. Check valves for secure fit.
5. Fill pool until water capacity is 90% (See Fig. 9), DO NOT
OVERFILL as this could cause the pool to collapse. In times of
heavy rainfall you may need to empty some of the water to ensure
the level is correct.
6. Check pool for any leaks at valves or seams, check ground cloth for
any evident water loss. Do not add chemicals until this has been
done.
7. In the event of a leak, patch your pool using the underwater adhesive repair patch provided.
Refer to the FAQ's for further information.
Fig. 9
Proper Water Level
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.
I ATTENTION: Do not use pump when pool is in use.
During the season of use of the swimming pool, the filtration system must be necessarily put into
service every day, enough for a long time to assure at least a complete renewal of the volume of
water.
POOL MAINTENANCE
Warning: If you do not adhere to the maintenance guidelines covered herein, your health might be
at risk, especially that of children. Pool water treatment is essential for the safety of the users. Using
E/F/G
L
chemicals inappropriately will cause property damage and personal injury.
NOTE: The pump is used to circulate the water and to filter small particles. In order to keep your
pool water clean and hygienic, you must also add chemicals.
5
Fig. 8
Fig. 10
0°
S-S-004372