Parkside PKS 1700 B2 Originalbetriebsanleitung Seite 46

on a workbench or a table if at all possible.
•
Support long workpieces (e.g. with a roller
table) to prevent them sagging at the end of a
cut.
6. Additional safety information on cros-
scut saws
•
Give these safety instructions to all persons
who work on the machine.
•
Do not use this saw to cut fire wood.
•
Caution! Hands and fingers may be injured
on the rotating saw blade.
•
Before you use the machine for the first time,
check that the voltage marked on the rating
plate is the same as your mains voltage.
•
If you need to use an extension cable, make
sure its conductor cross-section is big enough
for the saw's power consumption. Minimum
cross-section: 1.5 mm
•
If you use a cable reel, the complete cable
must be pulled off the reel.
•
Persons working on the machine should not
be distracted.
•
Note the direction of rotation of the motor and
saw blade.
•
After you have switched off the motor, never
slow down the saw blade by applying pressu-
re to its side.
•
Only fit blades which are well sharpened and
have no cracks or deformations.
•
Faulty saw blades must be replaced immedia-
tely.
•
Never use saw blades which do not comply
with the data specified in this manual.
•
It is imperative to make sure that the arrow on
the saw blade conforms with the arrow on the
machine.
•
Pull out the power plug and twist the blade
with your hand into the 45° and 90° po-
sitions in order to make sure that the blade
does not touch the turntable in any position. If
necessary, readjust the saw head.
•
It is imperative to make sure that all devices
which cover the saw blade are in good wor-
king order.
•
Never wedge the hinged saw blade guard in
open position.
•
Never dismantle the machine's safety devices
Anl_4300686.indb 46 Anl_4300686.indb 46
GB
2 .
- 46 -
or render them inoperative.
•
Damaged or faulty safety devices have to be
replaced immediately.
•
Never cut workpieces which are too small to
hold securely in your hand.
•
Avoid placing your hands in hazardous posi-
tions in which, one or both hands could touch
the saw blade if they slip suddenly.
•
The saw must not to be used for cutting round
workpieces.
•
There must be no nails or other foreign bodies
in the part of the workpiece that you wish to
saw.
•
Always stand to the side of the saw blade
when working with the saw.
•
Never load the machine so much that it cuts
out.
•
Always press the workpiece firmly against the
workbench and the stop rail to prevent the
workpiece wobbling or twisting.
•
Ensure that the off-cuts can be removed to the
side of the saw blade. Otherwise it is possible
that they will be caught by the saw blade and
catapulted out of the machine.
•
Never saw more than one workpiece at any
one time.
•
Never remove loose splinters, chips or jam-
med pieces of wood when the saw blade is
running.
•
To rectify faults or remove jammed pieces of
wood, always switch off the machine first. -
Pull out the power plug-
•
Refit all guards and safety devices immedia-
tely after you have completed any repairs or
maintenance work.
•
Be sure to observe the safety information and
operating and maintenance instructions issued
by the manufacturer, as well as the dimensi-
ons listed in the Technical Data.
•
It is imperative to observe the accident pre-
vention regulations in force in your area as
well as all other generally recognized rules of
safety.
•
Operation in enclosed areas is permitted only
with a suitable vacuum extraction system.
•
The crosscut saw has to be connected to a
230 V socket-outlet with minimum fusing of 10
A.
10.10.12 18:45 10.10.12 18:45