Herunterladen Inhalt Inhalt Diese Seite drucken

Safe Operation - Parkside PKS 1700 B2 Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für PKS 1700 B2:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

faces, persons or animals. Even a low output
laser beam can inflict injury on the eye.
Caution: It is vital to follow the work proce-
dures described in these instructions. Using
the equipment in any other way may result in
hazardous exposure to laser radiation.
Never open laser module.
When the laser is not going to be used for an
extended period of time, the batteries should
be removed.
Never use an optical instrument (for example
magnifying glass) to view the laser beam.
Check the laser for damage on a regular ba-
sis and always before use. To protect yourself
against injury, never use the equipment if it is
damaged.
Defective lasers have to be repaired by a cus-
tomer service workshop.
3. Safety information on the batteries
Never recharge the batteries. Danger of ex-
plosion.
Keep batteries out of the reach of children. Do
not throw batteries into the fire, short-circuit or
take them apart.
If necessary clean the contacts on the batte-
ries and equipment before inserting the batte-
ries.
Remove flat batteries immediately from the
equipment. Risk of leakage!
Always replace all batteries in one go. Only
use new batteries of the same make.
Avoid contact with skin, eyes and mucous
membranes. If you come into contact with
battery acid, rinse the affected pars at once
with plenty of clear water and seek immediate
medical assistance.
Do not expose batteries to extreme condi-
tions, e.g. do not place on heaters or in direct
sunshine. Increased risk of leakage.
Anl_4300686.indb 45
Anl_4300686.indb 45
GB
4. Maintenance and service
The following conditions can have an influ-
ence on noise impact on the operator:
- Type of saw blade (e.g. saw blades desig-
ned to reduce noise development)
- Material of the workpiece
- The force with which the workpiece is pu-
shed against the saw blade
Faults on the machine or its guards, safety de-
vices and blade must be reported to the per-
son in charge as soon as they are discovered.

5. Safe operation

Use a suitable blade for the material you wish
to saw.
Never use the drag, crosscut and miter saw
to cut any materials other than those specified
by the manufacturer.
Use only the transport devices to move the
equipment. Never use the guards for handling
or moving the equipment.
Use the saw only if it is in perfect condition
and properly maintained and only if the gu-
ards are correctly positioned.
When cutting miters, make sure that the de-
vice for swiveling the arm is fastened securely.
The floor around the machine must be level,
clean and free of loose particles, such as
chips and cutting residues.
The operator must receive proper training in
the use, adjustment and operation of the ma-
chine.
Only use properly sharpened saw blades. Do
not exceed the maximum speed specified on
the blade.
Be sure to only use spacers and spindle rings
specified by the manufacturer as suitable for
the intended purpose.
If the machine is equipped with a laser, this
laser may not be replaced by a different type
of laser. Repairs may only be carried out by
the manufacturer of the laser or one of his au-
thorized agents.
Do not remove any cutting residues or other
parts of workpieces from the cutting zone
while the machine is running and the saw unit
is not at rest.
Make sure that the machine is always secured
- 45 -
10.10.12 18:45
10.10.12 18:45

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Ian 79729

Inhaltsverzeichnis