Yamaha 01V Bedienungsanleitung Seite 297

PARAMETER CHANGE (7bit operation for type
0x10:edit buffer)
Reception
This message is received if [Parameter Change RX] is ON and the [Rx
CH] matches the Device Channel included in the SUB STATUS.
This is echoed if [Parameter Change ECHO] is ON.
When this is received, the specified parameter will be controlled.
Transmission
If [Parameter Change TX] is ON, this message is transmitted on the
[Tx CH] Device Channel when a parameter not specified in the
[Control Assign Table] is modified.
STATUS 11110000 F0 System Exclusive Message
Manufacturer's ID No.(YAMAHA)
ID No. 01000011 43
parameter change n=0-15(Device Chan-
SUB STATUS 0001nnnn 1n
nel No.1-16)
MODEL ID
GROUOP ID 00111110 3e
MODEL ID 00000100 04 Device code (01V)
7bit operation for edit buffer (type)
PARAM TYPE 00010000 10
DATA 0aaaaaaa dd0 address( H) high 7 bits of 14 bits address
address( L) low 7 bits of 14 bits address
0aaaaaaa dd1
data 7bit
0ddddddd dd2
: :
End Of Exclusive
EOX 11110111 F7
The valid range of addresses is 0x0000 - 0x03FF
PARAMETER CHANGE (bit operation for type
0x40:edit buffer)
Reception
When [Parameter Change RX] is ON, this message is received if the
[Rx CH] matches the Device Channel included in the SUB STATUS.
If [Parameter Change ECHO] is ON, this message will be echoed.
When this message is received, the specified parameter will be con-
trolled.
Transmission
If [Parameter Change TX] is ON, this message is transmitted on the
[Tx CH] Device Channel when a parameter not specified in the
[Control Assign Table] is modified.
STATUS 11110000 F0 System Exclusive Message
Manufacturer's ID No.(YAMAHA)
ID No. 01000011 43
SUB STATUS 0001nnnn 1n parameter change n=0-15(Device Chan-
nel No.1-16)
GROUOP ID 00111110 3e MODEL ID
Device code (01V)
MODEL ID 00000100 04
bit operation for edit buffer (type)
PARAM TYPE 01000000 40
DATA 0aaaaaaa dd0 address( H) high 7 bits of 14 bits address
address( L) low 7 bits of 14 bits address
0aaaaaaa dd1
0ddddddd dd2 data(bit0-2:change bit no.0-7, bit3:0=reset
1=set)
: :
EOX 11110111 F7 End Of Exclusive
The valid range of addresses is 0x0000 - 0x03FF
01V—Bedienungsanleitung
PARAMETER CHANGE (byte operation for type
0x01:system memory)
Reception
When [Parameter Change RX] is ON, this message is received if the
[Rx CH] matches the Device Channel included in the SUB STATUS.
When [Parameter Change ECHO] is ON, this is echoed.
When this is received, the specified parameter will be controlled.
System Exclusive Message
STATUS 11110000 F0
ID No. 01000011 43 Manufacturer's ID No.(YAMAHA)
parameter change or response
SUB STATUS 0001nnnn 1n
n=0-15(Device Channel No.1-16)
MODEL ID
GROUOP ID 00111110 3e
Device code (01V)
MODEL ID 00000100 04
PARAM TYPE 00000001 01 byte operation for system memory (type)
address( H) high 7 bits of 14 bits address
DATA 0aaaaaaa dd0
0aaaaaaa dd1 address( L) low 7 bits of 14 bits address
data( H) high 4 bits of 8 bits data
0000dddd dd2
0000dddd dd3 data( L) low 4 bits of 8 bits data
: : continuous address datas
End Of Exclusive
EOX 11110111 F7
The system memory will depend on the address, as follows.
0x0000 - 0x007F : setup memory(128byte)
0x0080 - 0x0147 : backup memory(200byte)
: card type(1byte)
0x0200
PARAMETER CHANGE (bit operation for type
0x41:system memory)
Reception
When [Parameter Change RX] is ON, this message is received if the
[Rx CH] matches the Device Channel included in the SUB STATUS.
When [Parameter Change ECHO] is ON, this is echoed.
When this is received, the specified parameter will be controlled.
System Exclusive Message
STATUS 11110000 F0
ID No. 01000011 43 Manufacturer's ID No.(YAMAHA)
parameter change or response
SUB STATUS 0001nnnn 1n
n=0-15(Device Channel No.1-16)
MODEL ID
GROUOP ID 00111110 3e
MODEL ID 00000100 04 Device code (01V)
PARAM TYPE 01000001 41 bit operation for system memory (type)
address( H) high 7 bits of 14 bits address
DATA 0aaaaaaa dd0
0aaaaaaa dd1 address( L) low 7 bits of 14 bits address
data(bit0-2:change bit no.0-7, bit3:0=reset
0ddddddd dd2
1=set)
:
:
End Of Exclusive
EOX 11110111 F7
The system memory will depend on the address, as follows.
0x0000 - 0x007F : setup memory(128byte)
0x0080 - 0x0147 : backup memory(200byte)