Yamaha 01V Bedienungsanleitung Seite 296

1.3 ACTIVE SENSING (Fe)
Reception
Once this message has been received, an interval of 300ms or more
during which no message is received will cause MIDI communica-
tions to be initialized, clearing Running Status etc.
STATUS 11111110 FE Active Sensing
2. TRANSMISSION CONDITION
CTL Tx ON
CONTROL CHANGE $BnH
PGM Tx ON
PROGRAM CHANGE $CnH
PARAM Tx ON
SYSTEM EXCLUSIVE
PARAMETER CHANGE
$F0H, $43H, $1nH
(RESPONSE FOR
PARAMETER REQUEST)
SYSTEM EXCLUSIVE
BULK DUMP $F0H, $43H, $0nH
BULK REQUEST $F0H, $43H, $2nH
USER DEFINE
MMC $F0H, $7FH, nnH, 06H
CTL ECHO ON
PGM ECHO ON
MIDI IN
PARAM ECHO ON
3. RECEIVE CONDITION
MIDI Rx CH?
CTL Rx ON
PGM OMNI ON
PGM Rx ON
CTL OMNI ON
PARAM Rx ON
PARAM OMNI ON
MIDI IN
BULK Rx ON
CTL ECHO ON
PGM ECHO ON
PARAM ECHO ON
4. PARAMETER CHANGE
BASIC FORMAT
STATUS
ID No.
SUB STATUS
GROUP ID
MODEL ID
PARAM TYPE
DATA
EOX
type
-----------------------------------------------------------------------------
MIDI TX CH?
0x00
0x01
0x02
0x03
0x04
MIDI OUT
0x05
0x10
0x40
0x41
0x43
PARAMETER CHANGE (byte operation for type
0x00:edit buffer)
Reception
This message is received if [Parameter Change RX] is ON and the [Rx
CH] matches the Device Channel included in the SUB STATUS.
If [Parameter Change ECHO] is ON, this will be echoed.
The specified parameter will be controlled when this message is
received.
$8nH NOTE OFF
$9nH NOTE ON/OFF Transmission
If [Parameter Change TX] is ON, this message will be transmitted on
$BnH CONTROL CHANGE
the [Tx CH] Device Channel when a parameter that is not specified
$CnH PROGRAM CHANGE
in the [Control Assign Table] is modified.
SYSTEM EXCLUSIVE
$F0H, $43H, $1nH
PARAMETER CHANGE
STATUS
$F0H, $43H, $3nH
ID No.
PARAMETER REQUEST
SUB STATUS
SYSTEM EXCLUSIVE
$F0H, $43H, $0nH, BULK DUMP
GROUOP ID
$F0H, $43H, $2nH, BULK REQUEST
MODEL ID
PARAM TYPE
DATA
MIDI OUT
EOX
The valid range of addresses is 0x0000 - 0x03FF
11110000 F0 System Exclusive Message
Manufacturer's ID No.(YAMAHA)
01000011 43
0pppnnnn pn p=mode 1:parameter change or response
for request, 3:parameter request
n=0-15(Device Channel No.1-16)
00111110 3e MODEL ID (digital mixer)
Device code (01V)
00000100 04
0ttttttt tt (type)
data 0
0ddddddd dd0
: :
data n
0ddddddd ddn
End Of Exclusive
11110111 F7
edit buffer ...byte operation format
system memory (setup, backup) ...byte operation format
function call (mem/lib recall, mem/lib store, clear, title)
controller (LCD/fader mode)...byte operation format
multiple link (fader mode, solo mode, title,,,)
remote meter (meter data)
edit buffer ...7bit operation format
edit buffer ...bit operation format
system memory (setup, backup) ...bit operation format
controller (key remote) ...bit operation format
System Exclusive Message
11110000 F0
01000011 43 Manufacturer's ID No.(YAMAHA)
parameter change or response
0001nnnn 1n
n=0-15(Device Channel No.1-16)
00111110 3e MODEL ID
Device code (01V)
00000100 04
00000000 00 byte operation for edit buffer (type)
address( H) high 7 bits of 14 bits address
0aaaaaaa dd1
0aaaaaaa dd2 address( L) low 7 bits of 14 bits address
0000dddd dd3 data( H) high 4 bits of 8 bits data
data( L) low 4 bits of 8 bits data
0000dddd dd4
: : : continuous address datas
End Of Exclusive
11110111 F7
01V—Bedienungsanleitung