Herunterladen Inhalt Inhalt Diese Seite drucken

AEG Electrolux FP 4200 Gebrauchsanweisung Seite 19

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

822_949_452 FP4200-4400_AEG.book Seite 16 Donnerstag, 12. Februar 2009 11:19 23
g
1
If this happens, proceed as follows.
Failure to follow this procedure can
result in damage to the appliance,
which is not covered by the guarantee.
0 Allow the appliance to cool down for
at least 15 seconds.
0 Turn the speed selector (fig. 1/I) left to
"0" position (fig. 16/➀).
0 Remove the mix container or all-pur-
pose bowl (fig. 16/➁ and ➂), as descri-
bed at the relevant point in these
operating instructions.
0 Remove the mains plug from the
socket (fig. 17/➀).
0 Lay the appliance on its back to gain
access to the bottom (fig. 17/➁).
0 Press the overload cut-out reset button
(fig. 1/N) on the bottom of the appli-
ance. If the appliance has cooled down
sufficiently, the button will engage
(fig. 17/➂). If it jumps back out, allow
the appliance to cool down a little lon-
ger, then repeat the process.
0 Once the reset button has engaged,
put the appliance back to its normal
working position (fig. 18/➀).
0 Plug the power lead back into the
mains socket (fig. 18/➁).
0 Replace the mix container or all-pur-
pose bowl (fig. 18/➂ and ➃), as descri-
bed at the relevant point in these
operating instructions.
0 The appliance is now ready for use
again. Turn the speed selector to the
right to the required position (fig.
18/➄) and continue with the function
that was interrupted.
Mixer
Preparing mixer
In order to fit the mix container, the
safety cover for the mixer drive (figs.
1/T and 4) must be removed.
0 Turn the safety cover clockwise and
remove.
– The red warning lamp (fig. 4/a)
flashes.
16
0 Place the mix container (figs. 1/B and
2) on the mixer drive (mark
mark
) and turn counter-clockwise
to the stop. The mix container is heard
to engage (mark
– The red warning lamp (fig. 4/a)
extinguishes.
0 Only FP4200: Place mixer cover (figs.
1/C and 3) on mix container and turn
until the nose of the cover is directly
above the handle. The cover can be
heard to engage.
The mixer can only be switched on
3
when the container and cover are fit-
ted correctly.
0 Only FP4400: Place mixer cover on
mix container.
The mixer can only be switched on
3
when the container is fitted correctly.
0 Fit closing cover (fig. 1/D) and lock.
Operating mixer
0 Open cover (fig. 1/C) and fill all ingre-
dients required in the container.
Caution: Do not exceed maximum fill-
ing volume of 1.5 litres!
During operation further ingredients
3
can be added through the filling inlet.
The sealing cover (fig. 1/D) can also be
used as a filling beaker for this pur-
pose. Close the filling inlet again
immediately every time to avoid
splashing.
0 Start the mixer: turn speed selector
(fig. 1/l) to the right to the desired
speed or press the pulse button
(fig. 1/J).
3
It is recommended to start at a slow
speed and then to increase the speed.
The mixer operates at maximum speed
by pressing the pulse button.
Refer to the section "Tips on using
mixer" for reference values for setting
the speed.
0 Switch off appliance: turn speed selec-
tor left to "0" position.
on
on mark
).

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Fp 4400Fp 4 series

Inhaltsverzeichnis