Parts Description; Installation - Makita DFJ206 Betriebsanleitung

PARTS DESCRIPTION

► Fig.1
1 Battery holder (10.8 V /
10.8 V - 12 V max)
(optional accessory)
5 Sleeve holder
9 Power cable

INSTALLATION

Installing or removing the battery
cartridge
CAUTION:
Always switch off the device
before installing or removing the battery
cartridge.
CAUTION:
Hold the battery holder and the
battery cartridge firmly when installing or remov-
ing the battery cartridge. Failure to hold the battery
holder and the battery cartridge firmly may cause
them to slip out of your hands and result in damage
to the battery holder and battery cartridge and/or a
personal injury.
► Fig.2: 1. Red indicator 2. Button 3. Battery cartridge
4. Battery holder (optional accessory)
To install the battery cartridge, align the tongue on the battery
cartridge with the groove in the housing and slip it into place.
Insert the battery cartridge all the way until it locks in place
with a small click. If you can see the red indicator on the upper
side of the button, it is not locked completely.
To remove the battery cartridge, slide it from the battery holder
while pressing the button on the front of the cartridge.
CAUTION:
Always install the battery car-
tridge fully until the red indicator cannot be seen.
Otherwise the battery cartridge may accidentally
fall out of the battery holder, causing injury to you or
someone around you.
CAUTION:
Do not forcibly install the battery
cartridge. If the battery cartridge does not slide in
easily, it is not being inserted correctly.
Attaching the battery holder
You can hang the battery holder on your waist belt.
To prevent the battery holder from dropping acciden-
tally, attach a strap using the strap hole and secure it.
► Fig.3: 1. Strap hole
For 18V and 14.4V battery holders
The battery holder has an anti-drop function. When
removing the battery holder from the belt, pull up the
battery holder while pressing the unlock button.
► Fig.4: 1. Unlock button
2 Battery holder (14.4 V
/18 V)
(optional accessory)
6 Battery pocket
10 Anti-slip rubber
(DFJ207, DFJ305 and
DFJ407 only)
3 Loop for name badge
7 Mesh pocket for ice pack
11 Hood
(DFJ207, DFJ305 and
DFJ407 only)
Installing or removing the fan unit
1. Turn the ring counterclockwise while lifting the
hook on it. Remove the ring when the mark on the ring
aligns with the slot on the fan unit.
► Fig.5: 1. Fan unit 2. Ring 3. Hook 4. Slot 5. Mark
2. Pass the head of the fan unit into the hole on the jacket.
Set the ring onto the fan unit and turn it clockwise until the
mark on the ring aligns with the mark further from the slot.
► Fig.6: 1. Mark 2. Ring 3. Fan unit
3.
Pass the strip through the loop on the fan unit and
fasten the snap button.
► Fig.7: 1. Strip
4. Attach the other fan unit to the jacket in the same way.
5. Connect the cable to the fan units. Support the
cable using the cable holder.
► Fig.8: 1. Cable 2. Cable holder
6.
Connect the other end of the cable to the battery
holder.
► Fig.9: 1. Battery holder
CAUTION:
Always use the strip and snap
button to secure the fan unit to the jacket. If the
fan unit falls, it may cause an injury, or damage to the
fan unit.
Follow the installation procedure in reverse when
removing it.
Attaching the filter set
Optional accessory
The filter set protects the fan unit from dust and powder.
We recommend that you use the filter set in a dusty or
powdery work place.
Insert the filter attachment between the jacket and fan
unit as shown in the figure.
► Fig.10: 1. Ring 2. Hole in the jacket 3. Filter attach-
ment 4. Fan unit 5. Filter
When tightening the ring, stop it at the mark near the
slot on the fan unit. After attaching the fan units, cover
the filter attachments with filters.
► Fig.11: 1. Mark 2. Slot
NOTICE:
Make sure that the filter fully covers
the filter attachment. For better protection against
dust and powder, tuck the skirt of the filter
between the jacket and filter attachment.
9 ENGLISH
4 Loop for arm badge
8 Fan unit
- -