Herunterladen Inhalt Inhalt Diese Seite drucken

Using The Guide Fence; Using The Rebate Depth Stop; Removing And Installing A Planer Blade; Replacing A Drive Belt - Parkside PEH 30 A1 Originalbetriebsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Using the guide fence (see Fig. I)
Q
A ttach the guide fence
the fixing screw
7
R elease the fixing nut
the desired distance.
R etighten the fixing nut
E xert some slight sideways pressure when guid-
ing the planer with the guide fence.

Using the rebate depth stop

Q
(see Fig. J)
A ttach the rebate depth stop
with the fixing screw
S et the desired rebate depth with the rebate
depth stop
.
12
M ake the required number of passes with the
planer until desired rebate depth is achieved.
Removing and installing a
Q
planer blade
DANGER OF INJURY!
Before you carry out any work on the device always
pull the mains plug out of the mains socket.
C AUTION! The sharp cutting edges of the plan-
er blade
present an injury hazard! Never
20
touch the cutting edges of the planer blade
The planer blade
has two cutting edges and it
20
can be fitted either way around.
R eplace the planer blade
edges are blunt.
D o not resharpen the planer blades
Reversing or replacing a planer blade
IMPORTANT INFORMATION:
Do not release the two Allen keys. They are used to
adjust the height of the blade shaft.
Adjustment is necessary only if you wish to use a
different planer blade type e.g. a profiled blade.
Always replace both blades at the same time to
avoid out of balance forces.
Preparing for use / Maintenance and cleaning
to the device with
6
.
and set the guide at
8
.
8
to the device
12
.
11
(see Fig. D + E)
20
when both cutting
20
.
20
NOTE: If you only release one blade first then you
can use the factory-fitted second blade for orientation
when you fit the new blade.
1. Release the 3 bolts of the cutting element
using the supplied open spanner
P ress the removable side guard
in the housing.
2. Push the cutting element
the blade shaft
3. Push the planer blade
the cutting element
4. Reassembly is carried out in the reverse order
with a reversed or new planer blade.
5. Planer blades
service address indicated (see section about
warranty).

Replacing a drive belt

Q
(see Figs. F + G)
Before you carry out any work on the device always
pull the mains plug out of the mains socket.
R elease the screws
cover
.
4
R emove the worn drive belt
F irst place the new drive belt
belt wheel
25
.
on to the large belt wheel
20
P ut the belt cover
fasten it into place with the screws

Maintenance and cleaning

Q
Before you carry out any work on the device always
20
pull the mains plug out of the mains socket.
A lways keep the device and the ventilation
slots clean. This way you will work more safely
and produce better results.
C lean out the planing debris removal port
regularly.
C lean out a blocked planing debris removal
port using suitable means (e.g. piece of wood,
air under pressure, etc.).
.
26
into the slot
21
sideways out from
18
.
17
sideways out from
20
.
18
can be obtained from the
20
DANGER OF INJURY!
and remove the belt
5
.
23
on to the small
23
and then pull the drive belt
by rotating it.
24
back into position and
4
.
5
DANGER OF INJURY!
18
23
3
GB/IE
11

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis