Werbung
GB
For correct and safe installation of the appliance,
please carefully read this manual and the other
documentation provided (see section "Precautions and
general advice").
Specifications, technical data, images and parts
supplied may be subject to change without prior
notice.
WATER CONNECTION
Disconnect the appliance from the
mains power supply before starting
operations.
• In any case, make sure to comply
with the current local regulations
regarding connection to the water
system.
• The appliance is supplied with a
water tube, 1.8 m long, already attached to the back of
the product.
• The water tube complies with IEC 61770.
• Remove the shipping tape from the gray coiled water
tubing on the rear of the appliance.
• Connect the transition connector (1) to the household
water supply (2).
• Open the water tap and check for and eliminate any
leaks.
• The appliance does not require adjustments or a water
drain.
ELECTRICAL CONNECTION
Connect the appliance to the mains power supply.
Electrical safety of the appliance can only be guaranteed if
it is correctly connected to an efficient, approved earthing
system.
POSITIONING AND LEVELLING YOUR
REFRIGERATOR
If the appliance seems unsteady or you want the doors to
close more easily, adjust the
appliance's tilt following the
instructions below (depending on
the model, as shown in the figures
on the right).
The refrigerator has two front
and two rear wheels at the base
of the product on each side and
two adjustable feet at the front
(see figure A).
1. Check the installation location to be sure you have at
least 1 cm clearance on all sides including the top.
2. Connect the appliance to the mains power supply.
3. Move the refrigerator into its final position.
4. Open both doors and remove
the plinth to locate the feet and
levelling bolts at the left and right
of the refrigerator base (where
present). The top bolt (1) will
adjust the rear wheel (if
provided), and the bottom bolt
(2) will adjust the front wheel (see figure B).
5. Use the wrench provided (if present) to adjust the
levelling bolts. Turn clockwise to raise the appliance, or
anticlockwise to lower it. It may take several turns of the
levelling bolts and/or feet to adjust the tilt of the
refrigerator.
6. After levelling the product, ensure that both feet touch
the ground for safe use.
Note: do not unscrew the levelling bolts and feet
too much as they could fall out.
Aligning the doors
If, after switching on the appliance and adjusting the
refrigerator and freezer doors, the doors are misaligned,
disconnect the appliance from the power supply and
adjust both doors as indicated in the diagram at the end of
this manual.
INSTALLING CUSTOM DOOR PANELS
• Installing customized panels
If you wish to install customized panels, they must be made
according to the dimension drawings.
• Flat panels
Flat panels of max. thickness 6.35 mm can be fitted in the
frames. Thinner panels are not recommended.
• Raised panels
A raised panel design can be created by screwing or gluing
wood panels to 6.35 mm backing or by using 16 mm stock
with 6.35 mm routed edges.
To allow room for fingers, it is advisable to arrange the raised
panels at a distance of 5.70 cm from the rear edge of the
handle.
• Weight requirements for raised inserts
- The refrigerator compartment door panel must not exceed 10
kg.
- Freezer compartment door panels must not exceed a total
weight of 7 kg.
INSTALLATION DIMENSIONS
AND REQUIREMENTS (G)
REMOVING THE FREEZER DOOR (A)
REMOVING THE REFRIGERATOR DOOR (B)
INSTALLING CUSTOM DOOR
PANELS (H)
MOUNTING THE FREEZER DOOR (C)
MOUNTING THE REFRIGERATOR DOOR (D)
HORIZONTAL ALIGNMENT OF FREEZER
AND REFRIGERATOR DOORS (E)
VERTICAL ALIGNMENT OF FREEZER
AND REFRIGERATOR DOORS (F)
A
B
3
Werbung
