Using Other Installed Drivers - Sharp AL-840 Bedienungsanleitung

STATUS MONITOR
M~sage sotunon
2:"7-
:'-3'2'i::l'J ~jSee''1iN
-,
..•. _ '.,-_.
__
..
,.,
..
~
.",
...
""',-
','
-'-'--"
" ,
...
,,-.--' -
~
,
--"
p.€!9,e:
Check Paper Tray: Out of Paper
The paper tray is out of paper or the paper did
Copier*4:
l orMlsfeed
not
f~ed
correctly. Printing cannot continue
Copier*5]
, '.,)
Julitir
yotilbad the
paper
or clear
the
mleteed-
-;' (:~:-'
Inth'e' papertray ,""
v.. •
I,,;'
,
Service'Erro~'
,
":,
-The
p~6duct-'i~as'd~tected
a
fatal
error ,._' ,
'"
Switch'Main PoWer OFhbhthe
Cbrlditi6n
and~ta.hn'ot
continue-Make a; n'dfEiI I'
product. Wait
a-pprbxlmate"Y:5)
'ofEihyspeCiffoSifbr
concltlonsor-ccdes» .
, ::).'
seconds. Switch
MalnPower"
"
THenWrn: theproeuct's main power
switch
to"-
ON. If The Product Error
OFF. Wait for':fiVe seconds. Then turn the
continues, Contact.your producfs.ma,in.ppwer switch to ON. If the
authorized
'SH..l}~P,SerVice
' "
;'p'roduct,error condition persists, 'please"
Center. ,
"
'
.ypn,tact:.Yql<!.I;.<iu'th,orized SHARP .Servlce
Center.
"
Communication Error The computer has lost,communications with -
The computer has lost
the product. Cancel the current operation.
communicaiions with the
Then furn the product's main power switch to
products. Cancel the current
OF~
qheck the,
cable'Gonn~c~ions
.carefully,
operation, turn the product off,
Wait five seconds, Then turn the product's' "
check the cable connection, main power switch to ON. Try the print job
then back on, retry the
again. If the product communications error
operation.
condition persists, please refer to the
I,;,
Operation manual .
,
'
.
,
'2:
See the section on DRUM CARTRIDGE REPLACEMENT.
'3:
See the section on INSTALLING THE TD CARTRIDGE.
'4:
See the sectton On MISFEED''REMOVAL.
rs.
See the sectlonon LOADING COPY PAPER.
USING
OTHER
INSTAI..LED,ORIVERS
If youuse an6the~, GDr p(iryteror.~ Wirrd,o'Ws. Printing System printer, interference between
printers may occurarid
prjnting~
may not
bejj~iformed
properly.
To. use another GDI,printer or a Windows 'PrjntingSystem printer, you must change the port
setting of the printercnver using the foUC?wh19 procedure.
-
20
§
Note
.
"~
--
"
,
.
i" :,,;';
I;, " '
r.o.L. ,
C' " " ", ," :-,'
"i"" , ,:':.' , ".':
If
~LOoth~~:prtrt~t,??es.,
net operate
p,~op~rly
when, the AL-800,
seri~~
printer
driver is setto "~rLE",,uninstall the,AL-BOO serie,s printer driver.
To uninstall thediive':see'UNINSTAL.l!NG PRINTER DRIVER on P'!ge 22.
_' ' " ' , ",' ,t ,,-' . "
",,'m' "