Safety Regulations - EINHELL DTA 25/2 Originalbetriebsanleitung

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Protect yourself and your environment from ac-
cidents by taking the appropriate precautionary
measures.
•
Do not use the stapler for a purpose for which
it is not designed.
•
Keep air tools safe from children.
•
Never use the equipment when you are not
rested or distracted.
•
Connect the compressed air using a quick-
lock coupling only.
•
Staplers may only be connected to lines/
hoses which do not allow the maximum
permitted pressure of the equipment to be
exceeded by more than 10%. A pressure re-
gulator (pressure reducer) with a downstream
pressure control valve must be fitted to the
compressed air hose if the pressure is higher.
•
The operating pressure must be adjusted by
a pressure reducer.
•
When using a pneumatically operated stap-
ler/nailer, only use the pressure required for
the specific operation to prevent an unneces-
sarily high noise level, excessive wear and
consequential faults.
•
Never use oxygen or combustible gases as a
power source. Danger of fire and explosion.
•
Always disconnect the equipment from the
compressed air source before tackling faults
or starting any maintenance work.
Anl_DTA_25_2_SPK7.indb 17 Anl_DTA_25_2_SPK7.indb 17
GB
•
Use only genuine spare parts. Repairs may
only be carried out by an authorized agent
of the manufacturer or by an alternative spe-
cialist in accordance with the specifications
contained in the operating instructions.
•
Wear the necessary protective clothing when
working with the stapler, in particular safety
goggles and protective gloves.
•
Do not exceed the maximum air pressure of
8 bar.
•
Do not direct the connected and loaded nailer
at other people.
•
Do not remove the earthing contact device.
•
Never leave the equipment unattended when
loaded.
•
Never use the equipment if defective.
•
Only use the types of staples/nails specified
in the technical data.
•
The equipment must always be depressu-
rized after disconnection.
•
Never use the equipment without staples/
nails.
•
Never point an operational stapler directly at
yourself or at any other person.
•
Whilst working with the stapler, hold it in such
a way that your head and body cannot be
injured in case of kickback caused by disrup-
tion of the power supply or by hard areas of
the workpiece.
•
Never trigger the stapler into the open air.
This is important to avoid the hazards of
free-flying staples and of overloading the
appliance.
•
For the purposes of transportation, the stapler
must be disconnected from the compressed-
air system, especially if you are using a lad-
der or are adopting an unusual posture.
•
In the workplace, carry the stapler only by its
handle and ensure that the trigger is inacti-
vated.
•
Make allowance for the workplace conditions.
Staples can potentially go straight through
thin workpieces or they can slide off workpi-
eces when working on corners and edges,
thus putting persons at risk.
•
For you own personal safety, always use
suitable protective equipment such as, for
example, hearing and eye protection.
•
Check that the trigger catch functions correct-
ly every time before you use the equipment.
You are allowed to start using the equipment
only if the device functions perfectly.
- 17 -
24.11.2016 13:14:06 24.11.2016 13:14:06