Specifications; Maintenance Service - Yamaha CDRW16G Bedienungsanleitung

Responsibility for loss of data, etc.
Yamaha will accept no responsibility for any damages (including
consequential or incidental) incurred by the customer or any
third party as a result of loss or impairment of the data stored on
the CD-R or CD-RW media, regardless of whether such loss
could have been or actually was foreseen by Yamaha.
Nor does Yamaha guarantee the media against any defect that
may render it unusable.
Do not subject the CD-R/RW drive to vibration or rough
handling. Never touch the optical pickup.

Specifications

Power supply: DC 5V
Current consumption: 1.8 A max
Dimensions (W × D × H): 128 mm × 129 mm × 12.7 mm
(projection not included)
Weight: 260 g
Included items: Screw × 2
Operating conditions
Temperature: 5–35 °C
Humidity: 10–80% RH (no condensation)
Placement: horizontal
Writing may not be possible in some cases due to
variations of quality between individual units of CD-R or
CD-RW media.
About copyright
This device is intended for use with material of which you
yourself are the copyright owner or for which you have received
permission from the copyright owner to duplicate. If you are not
the copyright owner or have not received permission from the
copyright owner to duplicate the material, you are in violation of
copyright law, and may be liable for damages and penalties. If
you are unsure of your rights to the material, please consult a
legal specialist.
Laser beam safety precautions
Carefully follow the installation instructions in the
manual for the main unit into which this device is being
installed. Taking actions that are not described in the
manual could cause the device to emit laser beams that
may cause injury.
If you look directly into the laser beam projected from the
optical pickup, your eyesight may be damaged. Follow the
cautions below:
• Do not open the optical pickup case.
• Do not peek inside the tray during operation.
Warning
Before installing this device, disconnect the power supply cable
of the product in which it is being installed, and disconnect any
cables that connect peripheral devices. Failure to do so may
cause electrical shock or malfunctions.
When installing, servicing, or replacing parts for this device, do
not perform any action that is not prescribed in the owner's
manual.
Do not disassemble the device. Laser beams inside the device
may damage your eyesight.
Do not apply excessive force to the electronic components or
connectors on the device, and do not disassemble it. Electrical
shock, fire, or malfunction may result.
Caution
Before touching this device, touch a metal part of the device into
which it will be installed, so that any static electricity in your
body will be discharged. Failure to do so will risk damaging the
electronic components by static electricity.
When handling this device, be careful not to touch the leads
(wires protruding from the electronic components) on the rear
side of the device. Injury may result.
When installing this device, be careful not to cut yourself on any
sharp edges or parts of this device or of the product into which
this device is being installed.
When installing this device, be careful not to drop screws etc.
into the product into which this device is being installed.
Do not allow this device to become wet, and do not place objects
on top of it. Doing so will cause malfunctions.
When installing this device, do not touch any unrelated parts or
circuit boards. Electric shock or malfunction may result.
Installing this device
For the procedure of installing this device, refer to the owner's
manual of the product into which the device is being installed. If
you have any questions, please contact your local Yamaha
distributor.
Cautions for installation
In order to install the device correctly, please pay attention to the
following points.
• Perform the installation according to the steps given in the directions,
making sure that the device is installed correctly and in the correct
orientation.
• Verify that this device has been installed correctly. If installation is
incorrect, the device might not work properly. Faulty connections or a
shorted power supply can cause malfunctions.
• Be careful not to lose any of the included screws.
• Using screws of the incorrect shape or length can cause malfunctions or
damage to the product. Use only the screws that were included with this
device.
• When installing or removing the device, be careful not to drop parts or
this device into the product.
• Make sure that the attaching screws are tightened firmly, and are not loose.
• Be careful not to touch any exposed metal portions of the device, or any
parts that are not essential to the installation process.
• The CD-RW drive is a precision device. Do not drop it or allow any
impact. Do not keep the unit in the place exposed to high temperature or
humidity.
• Before handling the device, be sure to touch a grounded metal surface to
remove any static electricity from your clothing and body. Otherwise,
static electricity may damage the device.
• Do not apply too much force by pushing the center of the device surface.

Maintenance service

• If the device malfunctions, consult your dealer. Other stores may not offer
Yamaha's authorized service.