Powerplus WALLABY Bedienungsanleitung

Do not try to separate the internal battery by yourself or try
W A R N I N G
to repair the product.
This product has an inverter which raises the voltage and output
HIGH VOLTAGE
to a much higher level than the internal battery.
Opening the product by yourself can cause serious injuries!
The POWERplus Wallaby is a compact and lightweight multifunctional AC/DC Power Station with a high quality
Lithium Polymer battery.
Before first use, charge the Wallaby by using the AC/DC charging adapter for at least 4 hours.
Contents
AC/DC charging
adapter
Solar charging
POWERplus Wallaby portable power supply
cable
fig. 1
This product has an integrated pure sine wave inverter; which can provide the most stable AC voltage to power your
AC electrical appliance up to 300W.
Charging by AC/DC adapter (fig. 2)
Press and hold the master ON/OFF until the Wallaby
activates. The Wallaby will only be charged when the
system is switched ON.
fig. 2
Connect the adapter to the mains (230V) and connect
the connector to the charging input on the side of the
Wallaby. This port is named 'CAR/ADAPTER'.
During charging, the battery status indicators will
illuminate in a moving pattern from 20% to 100%
(fig 3). When the battery is fully charged, the battery
on display will show a full battery.
Disconnect charger when fully charged.
When display battery icon only shows 20% battery
capacity (fig. 3b), charge the Wallaby as soon as possible.
fig. 3
INPUT
fig. 3b
W
DC OFF
W
AC OFF
Charging by solar power (fig. 4)
Press and hold the master ON/OFF until
the Wallaby activates. The Wallaby will only
be charged when the system is switched
ON.
The Wallaby can be charged by a solar
cell of 14V-40V and a wattage of maximum
120W.
Connect the supplied solar charging cable
to the solar panel (Direct to the panel.
When panel has built in charging controller,
this should be passed as the Wallaby uses
its own built in MPPT charging controller).
Now connect the solar charging cable with
the Wallaby. The port is named PV.
Charging indication on the display will be
same as described under charging by
AC/DC adapter above.
Disconnect solar panel when Wallaby is
fully charged.
When display battery icon only shows
20% battery capacity (fig. 3a), charge the
Wallaby as soon as possible.
In the charging modes, the input current
is visible on the display under 'INPUT'.
ATTENTION:
NEVER CHARGE THE WALLABY WITH AC/DC OR CAR ADAPTER AND SOLAR PANEL AT THE SAME TIME !
Cigarette plug 12V
car charger
The POWERplus Python (not included) is compatible with this power station
Smart jump starter
with cable clamps
1) Handle
2) Solar charging port
3) Car adapter charging port
AC adapter charging port
4) Jump starter output
5) Master ON/OFF button
6) DC power ON/OFF button
7) AC power ON/OFF button
Charging by 12V car charger
8) Power ON/OFF indicators
Plug the cigarette plug into your cigarette plug input socket from your car and connect the other end of the cable
9) LCD display with the input port (see fig. 2). For the rest of the charging procedure, please refer to charging by AC/DC adapter.
10) USB outputs
Please be aware that charging by car battery can drain your car battery. To prevent this, you can decide to charge
11) DC 12V outputs
only by car battery when the motor is running.
12) DC 12.6V cigarette plug output
13) AC 220V outputs
How to use the AC and DC outputs
Press and hold the master ON/OFF
button until the display illuminates and
the LED right from the button illuminates
as well.
To activate the DC output (2 * 6mm ports,
cigarette lighter input and 4 * USB outputs)
press and hold the DC ON button. The LED
right from the DC ON button will illuminate
and the display shows 'DC ON'.
To activate the 2 * AC output, press and
hold the AC ON button. The LED right from
the AC ON button will illuminate and the
display shows 'AC ON'.
To switch off the functions, press and hold
the buttons. The LEDs right will turn off
which indicates the function is OFF.
After a few seconds the backlight of the display turns off. Press one of the three buttons once to activate the
backlight function of the display again for a few seconds.
When you are not using a function, please switch off this function to save the battery.
When you connect an appliance to the Wallaby, the display shows the energy consumption.
In case the ON/OFF button is ON, but both DC and AC function are OFF, the Walliby will automatically shut down after
10 minutes. The Walliby will also shut down when the remaining battery capacity is lower than 10%.
fig. 4
A
B
Charging cable supplied with Wallaby
INPUT
DC ON
DC ON
AC ON
AC ON
1
2
3
4
Using the jump starter
The Wallaby can jump start a vehicle with an engine size of less then 4 litres.
Make sure the battery capacity of the Wallaby is at least 60%.
1) Clamp the red clamp to the vehicle's positive pole of the battery and the black clamp to the negative pole.
2) Plug the other end of the smart jump start cable into the output called 'CAR JUMP STARTER (4 in fig. 1)
3) Now start the engine of the vehicle as normal
4) After starting, take out the smart jump start cable out of the Wallaby and then remove the cable clamps from the
battery of the vehicle.
Important safety issues when using the jump start function:
• Make sure the clamps are tightly attached to the poles of the vehicle's battery
• Never connect the red and black clamps with each other, otherwise this can cause injuries
• Remove the cable within 30 seconds after starting the vehicle, otherwise it can cause damage to the Wallaby or
even can cause injuries
• Jump starter is only allowed to be used by adults and people familair with jump starting procedure.
Security and maintenance
1) Do not short-circuit the Wallaby
2) Keep away from high temperatures, do not dispose to fire, water or other liquids. Do not expose the Wallaby
to direct sunlight.
3) Keep away from high humidity and dust. Do not charge below 5 degree Celsius. The Wallaby has built in
safety and will stop charging when temperature will be below 5 degrees Celsius.
If temperature reaches below - 20 degrees Celsius, system will stop the AC and DC output function and will
switch off automatically
4) Do not disassemble or reassemble the Wallaby.
5) Do not drop, place heavy objects on the product, or allow strong impact.
6) This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
7) Children should be supervised to ensure that they do not play with the appliance.
8) Do not cover the device with towels, clothing or any other item.
9) Do not charge the unit over the required time.
fig. 5
10) Disconnect the unit when fully charged.
11) Use the unit properly to avoid electronic shock.
12) This appliance is equipped with a high quality Lithium-Ion Battery. Although this kind of battery has very low
memory effect, we advise to charge the appliance every 3 months to ensure the lifetime of the battery.
If you store the Wallaby for a long time, please be sure to charge the battery full.
13) Store the Wallaby in a place with a temperature between 10 - 30 degrees Celsius.
14) When charging keep away from TV, radio, communication equipment to avoid interference.
15) Some portable devices may need to be set in charge mode to charge. Please refer to the corresponding
manual of the devices for more information.
16) The Wallaby has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery,
as you may damage the device or you can be injured by electrical shock.
17) The battery can be charged and discharged fully over 500 times, but it will eventually wear out.
18) When battery capacity is less then 10%, recharge immediately. When not recharged within a few weeks,
the battery can be damaged and cannot be recovered/recharged anymore.
19) Always switch off the Wallaby when not in use.
20) If you connect AC appliances which drain a high power (i.e. a refridgerator), the battery can drop very quickly
and the battery may not provide the full 400Wh.
21) When using the Wallaby, the outer shell can become a little bit warm. This is completely normal.
Technical details:
Built in battery High Quality Lithium Ion / 18650 cells 11.1V/36Ah battery pack / 400Wh / 9~12.6V
Inverter Pure Sine Wave DC-AC inverter, output max. 300W (peak 450W)
Dimensions 230 x 150 x 250 mm
Weight 5.2 kg
Input DC 14 ~ 40V
Fully charged time AC/DC charger (70W)
Car charger (48W)
Solar panel (40W) - full sun
Operation environment Charge 0~45 degrees Celcius
Discharge -10~60 degrees Celcius
Humidness 10%~90%
Output 2* AC 220V 300W max.
2 * 12V/3A 6mm 36W max.
1 * 12.6V/10A cigarette plug input 120W
4 * USB 5V 2*2.1A and 2*1A
The system detects failures and display this as failure codes in the display:
E01 System over-temperature protection
E02 Battery Over Voltage Protection
W
E03 Battery Damage Protection
E04-05-06 Battery Strings Over Voltage
E07-08-09 Battery Strings Low Voltage
E10 Low Temperature Discharging Protection
W
E11 Battery Low Voltage Detection
E12 Inverter Over Current Protection
E13 Inverter Over Load Protection
E14 Inverter Short Circuit Protection
E16 Charging Over Voltage Protection
E17 Low Temperature Charging Protection
E19-20-21-22 12V Outputs Overload Overcurrent Protection
E23-E24 USB output over current
What to do after end of lifetime / recycling
This appliance is equipped with an internal battery. This battery can be replaced with a similar battery after lifetime
of the battery. Do not replace the battery by yourselves. This product has an internal inverter which powers up the
voltage to 220V. This can generate shocks which can cause serious injuries.
Only replace the battery by a qualified electrician.
Deliver the battery after lifetime to a battery collection
point for recycling.
Deliver the appliance after lifetime to an appliance
collection point for recycling.
6- 8 hours
10-15 hours
12-18 hours
Ambient temperature > 45 degrees Celsius
System will start again when Wallaby cools off
Disconnect the charger and restart the system
Contact your local dealer for service
Disconnect the charger and restart the system
Charge the system and restart after fully charged
Charge if ambient temperature is < -20 Celsius
Charge the system and restart after fully charged
Check if AC output is overloaded or short-circuit
Check if AC output is overloaded
Check if AC output is overloaded or short-circuit
Check if input voltage exceeds the maximums
Ambient temperature is < 0 degrees Celsius
Check if outputs are overloaded / short-circuit
Check if outputs are overloaded / short-circuit