Exsys EX-S96102-2 Anleitung

CONNECTORS
U8:
Pin Assignment Pin Assignment
1 3.3 Volt (Orange) 7 5 Volt (pre-charge)
2 3.3 Volt (Orange) 8 5 Volt (Red)
3 3.3 Volt (pre-charge) 9 5 Volt (Red)
4 Ground (Black) 10 Ground (Black)
5 Ground (Black) 11 Reserve
6 Ground (Black) 12 Ground (Black)
To guarantee the full 900mA at all ports of the EX-S96102-2, it is recommended that the card
be connected with the power supply of the PC.
Please make sure you connect the plug in the right direction.!
Never connect or release the plug while the PC is supplied with power!
HARDWARE INSTALLATION
Please note the following installation instructions. Because there are large differences between the
PC's, we can give you only a general installation instructions for the EX-S96102-2. Please refer
your computer's reference manual whenever in doubt.
1. Turn off the power to your computer and any other connected peripherals.
2. Remove the mounting screws located at the rear and/or sides panels of your Computer and
gently slide the cover off.
3. If necessary please install now the external power supply to the card (see at Jumper
Setting & Connectors at U8).
4. Locate an available PCIe expansion slot and insert the card. Make sure that the card is
plugged in correctly.
5. Then attach the card with a screw to the rear panel of the computer.
6. Gently replace your computer's cover and the mounting screws.
DRIVER INSTALLATION
Windows XP/ Vista/ 7/ Server 2003 & 2008R2
After the hardware installation is complete, the operating system automatically detects the card
and installs it. If the driver should not be installed automatically, please download the driver from
our homepage (www.exsys.de) or (www.exsys.ch) first. Now select the folder of your operating
system and install the driver. Follow the installation instructions and complete the installation.
Important! Restart your PC after the installation.
Follow the installation instructions and complete the installation.
Windows will now install automatically you right driver for your particular operating system. After
the installation the operating system detects the card and automatically install them.
5
DRIVER INSTALLATION
CHECK INSTALLED DRIVER:
Open the >Device manager<. Now you should see at „USB-Controller" the following new entry's:
Pin Assignment
13 12 Volt (pre-charge)
14 12 Volt (Yellow)
15 12 Volt (Yellow)
If you see this or a similar information the device is installed correctly.
Windows 8.x/ 10/ Server 2012R2 / Server 2016
After the hardware installation, the operating system will recognize the device automatically and
install the drivers.
CHECK INSTALLED DRIVER:
Open the >Device manager<. Now you should see at „USB-Controller" the following new entry's:
If you see this or a similar information the device is installed correctly.
Germany: Switzerland:
EXSYS Vertriebs GmbH EXSYS Vertriebs GmbH
Industriestrasse 8 Dübendorfstrasse 17
61449 Steinbach 8602 Wangen
www.exsys.de www.exsys.ch
6
EX-S96102-2
Anleitung
Vers. 1.0 / 07.12.20
AUFBAU
C11 & C12:
2x externe USB 3.2 (Gen1)
A-Buchse
BESCHREIBUNG & TECHNISCHE DATEN
Die EX-S96102-2 ist eine USB 3.2 (Gen1) PCIe Karte. Sie ist mit 2 externen Ports ausgestattet,
die jeweils 900mA Strom zu Verfügung stellen. Die EX-S96102-2 unterstützt die volle Leistung
von 900mA an beiden externen Ports ohne das Sie zusätzlichen Strom vom PC-Netzteil benöti-
gen. Sie unterstützt alle PCIe Slots von x1 bis x16. Der PCI-Express Bus unterstützt optimal die
Leistung des schnellen Renesas Chipsatz. Die EX-S96102-2 gewährleistet so eine sichere
Datenübertragung und exzellente Performance von bis zu 5Gbit pro Sekunde! Sie unterstützt
alle USB Anschlüsse von 1.1 bis 3.2. Mit der EX-S96102-2 wird ein Low Profile Bügel mitgelie-
fert für schmale PC-Gehäuse bis maximal 8cm Bauhöhe.
Kompatibilität: PCI-Express x1 bis x16
Betriebssysteme: Windows XP/ Vista/ 7/ 8.x/ 10/ Server 20xx
Anschlüsse: 2x USB 3.2 Gen 1 A-Buchse extern, 1x 4-pin Molex
Lieferumfang: EX-S96102-2, Low Profile Bügel, Anleitung
Zertifikate:
ANSCHLÜSSE
J1 & J2:
USB 3.0 Pin's
Pin Signal
5 SSTX+
6 SSTX-
7 GND
8 SSRX+
9 SSRX-
1
U8:
SATA 15 Pin Power
Anschluss vom PC-Netzteil
USB 2.0 Pin's
Pin Signal
1 VCC
2 DATA-
3 DATA+
4 GND