Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
appears on the display
Once the set time has elapsed, an acoustic signal sounds and
The oven will switch off automatically.
To change the cooking time, use button "-" or "+". Return to point 3 chapter "Selecting the cooking time".
1.
Turn knob 1 back to "0".
The time of day appears again on the display.
To increase the cooking duration, use the "-" or "+" button.
Setting end of cooking time
By using this function it is possible to preset the end of cooking time. The maximum programmed cooking time is 23 hours and
59 minutes.
1.
Proceed as described in points 1 and 2 of the section "Selecting the cooking time".
2.
Press "set" to set the end of cooking time: the indicator
3.
Set the end of cooking time using button "-" or "+".
4.
Press "ok" to confirm the end of cooking time.
The oven will turn on automatically at the end of cooking time minus cooking time: the indicators
the symbols
light up.
Timer
The timer can only be set when the oven is not in use and allows a maximum setting of 6 hours.
To set the timer:
1.
Leave knob 1 on "0". The display shows the time of the day.
2.
Press "set". The indicator
Use buttons "-" or "+" to set the desired time.
3.
Press "ok" to confirm the selection.
Once the set time has elapsed:
An acoustic signal sounds and flashes on the display
Press "ok": the acoustic signal stops. The time of day appears again on the display.
KEY-LOCK
This function can be used to lock the programmer keys and the oven knobs.
1.
To activate it, turn knobs 1 and 5 to "0", press "ok" and "-" at the same time for 3 seconds. The indicator
symbol
lights up.
2.
Once activated, the oven functions will not operate.
3.
To deactivate the lock, repeat the sequence described in point 1.
COOKTOP FUNCTIONS TABLE (depending on model)
GENTLE HEAT
HEAT MAINTENANCE
FAST BOIL
MULTIZONE
next to the symbol
lights up.
.
COOKTOP CONTROL KNOBS
To allow dough to rise, to soften butter taken from the fridge, to keep baby bottles or food warm,
also for making yoghurt, melting chocolate, etc.
This function is only available when the residual heat indicator is on. For this function, make sure
the residual heat indicator of the desired hotplate is on. Turn the knob to
function, change the position of the knob.
To maintain a constant temperature of 60° until the end of cooking. To select this function, turn
the knob to
.
This function is used to bring water to the boil rapidly and remains on for a preset time. At the
end of the preset time, the cooktop automatically returns to the maximum power setting. This
function can be selected even during cooking. Important: before selecting this function, make
sure the pot is positioned on the selected hotplate in order to avoid any damage to the cooktop
surface. The stated performance values for this function are those guaranteed for all glass
ceramic cooktops. For this function, place the pot on the selected hotplate and turn the knob
to
. To deselect, change the position of the knob.
The multizone symbol, featured on the knobs, can only be switched on for those hotplates of the
cooktop equipped with double or triple zone function. These functions extend the heating area
of the cooktop in order to allow the use of large, oval or rectangular pots or cooking receptacles.
To switch on the dual zone (if available), turn the knob to
indicator for the hotplate begins to flash. To switch on the triple zone function (if available), wait
until the LED begins flashing quickly. Select the power setting required by turning the knob anti-
clockwise. The residual heat indicator remains on to indicate that the cooktop is in use. To
deselect, turn the knob to"0".
appears on the display.
lights up next to the symbol
GB22
.
on the display above
next to the
. To deselect the
and wait until the residual heat
Werbung
Inhaltsverzeichnis
