Presentation; Product Description; Intended Use - Dover Vsg Rav.td2Wf Übersetzung Der Originalanleitung

TABLE OF CONTENTS
2

PRESENTATION

2.1

PRODUCT DESCRIPTION

• Product name:
• Product description:
2.2

INTENDED USE

CCD2.0WIFI systems are pieces of equipment intended for the complete detection of the characteristic angles of vehicles.
Angle detection is carried out by four sensors with microprocessor technology and an infrared measuring and data transmission
system (without using cable connections between the sensors).
Data is transmitted by the front sensors via RADIO using a Bluetooth-compatible connection.
The maximum pitch length of the vehicle allowed to ensure data transmission and angle measurement is 4.5 m.
Temperature range for use if the equipment between 0 and 40°C.
• During the operation and maintenance of this machine, it is absolutely essential to comply with all the safety and accident-prevention
regulations in force.
• The equipment must only be used by authorised and adequately trained personnel.
• During the operation and maintenance of this machine, it is absolutely essential to comply with all the safety and accident-prevention
regulations in force.
• The equipment must only be used by authorised and adequately trained personnel.
• This equipment must only be used for the purpose for which it is expressly designed.
• The supplier shall not be held responsible for any damage to people, animals and property caused by the improper use of the
machine.
• The installation of accessories and spare parts must be performed by personnel authorised by the Manufacturer and original
accessories and spare parts must be used.
• The machine must only work in places where there is no danger of explosion or fire.
• The removal or modification of safety devices or of warning signs placed on the machine can cause serious danger and constitutes
a violation of the European safety standards.
• Before carrying out any maintenance on the system, it is necessary to disconnect the power supply.
• If in doubt, do not interpret, contact technical assistance in advance in order to receive information to be able to perform operations
in conditions of maximum safety.
• Prevent unauthorised personnel from approaching the wheel aligner during use.
WARNING
• For safety reasons, insert the cable in an earthed AC (Alternate Current) socket.
Risk of fire and explosion! To reduce this risk, the machine must be used only in places where there is no risk of fire or explosion.
•
This product must be installed and used only within licensed workshops.
Risk of electric shock! Never open the system. For continuous protection against electric shock, the console must be connected
•
to a reliable earthing system. Do not remove the earthing connection. If the socket in the facility does not have an earthing
connection, do not modify the connection plug.
• This equipment must only be used for the purpose for which it is expressly designed.
VSG ITALY S.R.L. disclaims all liability for persons, animals and property caused by misuse of the machine.
• Accessories and spare parts must be installed by VSG ITALY S.R.L. authorised personnel and only original accessories and spare
parts must be used. It is also not permitted, in any way, to replace batteries using non-original batteries. It is necessary to use
only the manufacturer's original batteries on the measuring heads.
• The removal or modification of safety devices or of warning signs placed on the machine can cause serious danger and constitutes
a violation of the European safety standards.
• Before carrying out any maintenance on the system, it is necessary to disconnect the power supply. In case of doubt, do not
improvise but rather contact VSG ITALY S.R.L. technical support to receive instructions and carry out the necessary procedures
under safe conditions.
• The operator must wear safety footwear to avoid damage to their feet, caused by the accidental falling of clamps or measuring
heads. Use footwear with certified protection according to the EN ISO 20345 standard.
• The operator must wear protective gloves when handling the clamps. Use gloves according to the EN 388 standard.
• Prevent unauthorised personnel from approaching the wheel aligner during use.
• Use only the supplied cables. In the event of breakage or a fault, consult qualified service personnel.
• Never try to use the equipment if it is damaged, if it works incorrectly, if it has been partially disassembled and if any components,
including cable and plug, are missing or damaged.
CCD2.0WIFI WHEEL ALIGNERS
CCD wheel aligner
RAV.TD2WF
ROT.TD2WF
SPA.TD2WF
2015-M366-00 EN-73