Operating Elements And Connections; Safety Notes; Setting Into Operation - Monacor Best.-Nr. 13.1590 Bedienungsanleitung

Please unfold page 3. Then you can always see the
GB
operating elements and connections described.

1 Operating Elements and Connections

1 Mounting bracket
2 Mounting screws, by unscrewing them the mount-
ing bracket can be removed
3 VOLUME control
4 Signal input jacks for connection to the line output
of an audio unit (mixer, CD player, etc.)
5 Terminal strip OUTPUT for connection of the pas-
sive speaker system
6 Tone controls for the HIGH and LOW frequencies
7 Mains jack for connection to a mains socket
(230 V~/50 Hz) via the supplied mains cable
8 Support for the mains fuse;
only replace a blown fuse by one of the same type
9 POWER switch
10 POWER LED

2 Safety Notes

This unit corresponds to all directives of the EU and is
therefore marked with
WARNING The unit is supplied with hazardous
mains voltage (230 V~). Leave servic -
ing to skilled personnel only. Inexpert
handling may cause an electric shock
hazard.
It is essential to observe the following items:
G
The unit is suitable for indoor use only. Protect it
against dripping water and splash water, high air
humidity, and heat (admissible ambient temperature
range 0 – 40 °C).
G
Do not place any vessels filled with liquid, e. g. drink-
ing glasses, on the unit.
G
Do not set the unit into operation, and immediately
disconnect the mains plug from the mains socket if
1. there is visible damage to the unit or to the mains
cable,
2. a defect might have occurred after a drop or simi-
lar accident,
3. malfunctions occur.
The unit must in any case be repaired by skilled per-
sonnel.
G
Never pull the mains cable to disconnect the mains
plug from the mains socket, always seize the plug.
G
For cleaning only use a dry, soft cloth, by no means
chemicals or water.
G
No guarantee claims for the unit and no liability for
any resulting personal damage or material damage
will be accepted if the unit is used for other purposes
than originally intended, if it is not correctly connect -
ed, operated, or not repaired in an expert way.
6
.
G
Important for U.K. Customers!
The wires in this mains lead are coloured in accord -
ance with the following code:
green/yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the ter minals in your plug, pro-
ceed as follows:
1. The wire which is coloured green and yellow must
be con nected to the terminal in the plug which is
mark ed with the letter E or by the earth symbol
or coloured green or green and yellow.
2. The wire which is coloured blue must be con-
nected to the terminal which is marked with the
letter N or coloured black.
3. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
Warning - This appliance must be earthed.
If the unit is to be put out of operation de fini-
tively, take it to a local recycling plant for a
disposal which is not harmful to the environ-
ment.
3 Applications
This set of speaker systems consists of an active
speak er system with a 2-channel amplifier and a pas-
sive speaker system. The speaker cabinets are de -
signed as bass reflex systems. As 2-way systems they
are equipped with a bass speaker and a dome tweeter
each. With this set, existing HiFi stereo systems can be
extended in an optimum way. However, the speaker
systems can also be used for PA and DJ applications.

4 Setting into Operation

4.1 Setting up and mounting
1. For setting up the speaker systems as desired,
screw off the mounting brackets (1). For this pur-
pose unscrew the two mounting screws (2).
2. For using the speaker systems as wall speakers,
fasten them with screws to the wall via their mount-
ing brackets (1). For better handling, screw off the
brackets first. For this purpose unscrew the two
mounting screws (2). Then fix the brackets to the
wall and fasten the speaker systems with screws to
the brackets.
4.2 Making the connections
Only make or change all connections with the active
speaker system switched off.
1) Connect the terminal strip OUTPUT (5) via a
speak er cable (e. g. series SPC-... from MONA-
COR) to the terminal strip INPUT of the passive
speaker system. Connect the red terminals with
each other and the black terminals with each other.