Herunterladen Inhalt Inhalt Diese Seite drucken

Replacing The Power Cable; Disposal And Recycling; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TH-CS 1200/1 Originalbetriebsanleitung

Handkreissäge
Vorschau ausblenden Andere Handbücher für TH-CS 1200/1:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
operate accidentally.
Ensure that you do not cover or block the
ventilation openings whilst working with the tool.
Do not slow down the saw blade after you switch
it off by pressing it sideways.
Important! Do not put down the machine until the
saw blade has reached a complete standstill.
Important. Carry out a trial cut in a piece of
waste wood
6.4 Changing the saw blade (Fig. 10-11)
Important. Always pull out the power plug
before doing any work on the circular saw!
Use only saw blades which comply with standard EN
847-1 and are of the same type as the saw blade
supplied with this circular saw. Ask your dealer for
advice.
Push back and secure the moving swing guard
hood (19) using the lever for the swing guard
hood (15).
Use the saw blade wrench (13) to apply
counterpressure to the flange (18).
Undo the screw to secure the saw blade (17)
using the Allen key (a).
Remove the flange (18) and the saw blade (12) in
a downwards direction.
Clean the flange and insert the new saw blade.
Pay attention to the running direction (see arrow
on the guard hood and saw blade).
Tighten the screw to secure the saw blade (17),
check it runs true.
Before you press the On/Off switch, make sure
that the saw blade is correctly fitted and that
moving parts run smoothly and the clamping
screws are tightened securely.

7. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
8. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the motor
n
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
n
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
n
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician.
Important! The carbon brushes should not be rep
laced by anyone but a qualified electrician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
Type of machine
n
Article number of the machine
n
Identification number of the machine
n
Replacement part number of the part required
n
For our latest prices and information please go to
www.isc-gmbh.info

9. Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.
10. Storage
Store the equipment and accessories out of children's
reach in a dark and dry place at above freezing
temperature. The ideal storage temperature is
between 5 and 30 °C. Store the electric tool in its
original packaging.
GB
15

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

43.309.36

Inhaltsverzeichnis