Adaptation to various types of gas
(Fig. 7) Should the appliance be pre-set for a
different type of gas than that available, proceed as
follows:
• replace the injectors (Fig. 7) with the
corresponding type of gas to be used (see table
"Uses characteristics").
• to adjust to the minimum, use a screwdriver on
the screw placed on the tap (Fig. 8) after
turning the tap to its minimum position. For
LPG (butane/propane) screw tight.
GB
Abb. 8 - Fig. 8 - êËÒ. 8
èËÒÔÓÒÓ·ÎÂÌË Í
èËÒÔÓÒÓ·ÎÂÌË Í
èËÒÔÓÒÓ·ÎÂÌË Í
èËÒÔÓÒÓ·ÎÂÌË Í
èËÒÔÓÒÓ·ÎÂÌË Í
Û„ÓÏÛ ÚËÔÛ „‡Á‡
Û„ÓÏÛ ÚËÔÛ „‡Á‡
‰Û„ÓÏÛ ÚËÔÛ „‡Á‡
Û„ÓÏÛ ÚËÔÛ „‡Á‡
Û„ÓÏÛ ÚËÔÛ „‡Á‡
(ÒÏ. êËÒ. 7) ÖÒÎË ÔË·Ó ËÁ„ÓÚÓ‚ÎÂÌ Ì ‰Îfl
Ú‡ÍÓ„Ó ÚËÔ‡ „‡Á‡, ÍÓÚÓ˚È ËÏÂÂÚÒfl ‚ ̇΢ËË,
ÌÂÓ·ıÓ‰ËÏÓ ‚˚ÔÓÎÌËÚ¸ ÒÎÂ‰Û˛˘ÂÂ:
- ÙÓÒÛÌÍË (ÒÏ. êËÒ. 7) Á‡ÏÂÌËÚ¸ ̇ ÚÂ, ÍÓÚÓ˚Â
ÒÓÓÚ‚ÂÚÒÚ‚Û˛Ú Ëϲ˘ÂÏÛÒfl ‚ ̇΢ËË ÚËÔÛ
„‡Á‡ (ÒÏ. "íÂıÌ˘ÂÒÍË ‰‡ÌÌ˚Â")
- èË ÛÒÚ‡ÌÓ‚Í ÛÓ‚Ìfl ÏËÌËχθÌÓÈ ÔÓ‰‡˜Ë
„‡Á‡ ˚˜‡„ ͇̇ ÔÓ‚ÂÌÛÚ¸ ‚ ÔÓÎÓÊÂÌËÂ
ÏËÌËÏÛÏ Ë ÒÓÓÚ‚ÂÚÒÚ‚Û˛˘ÂÈ ÓÚ‚ÂÚÍÓÈ
‚‡˘‡Ú¸ „ÛÎËÓ‚Ó˜Ì˚È ‚ËÌÚ (ÒÏ. êËÒ. 8). èË
ËÒÔÓθÁÓ‚‡ÌËË ÊˉÍÓ„Ó „‡Á‡ (·ÛÚ‡Ì-ÔÓÔ‡Ì)
Á‡‚ÂÌÛÚ¸ ÍÂÔÍÓ Â„ÛÎËÓ‚Ó˜Ì˚È ‚ËÌÚ.
RU
23