Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
The operating temperature range (outdoor temperature) for cooling is 18 ℃ ~ 52 ℃ ; The heating
NOTE:
temperature range for the low temperature system model is -15 ℃ ~ 24 ℃ ; The heating temperature
range with low temperature system is -20 ℃ ~ 24 ℃ .
need to follow the local safety standards and to provide for appropriate protection systems on power
Indoor unit installation
circuits electric .
A magnetothermic switch of suitable size must be provided in order to protect the system from possible
Qualifications required for installation and maintenance
overloads and short circuits.
All workers who install refrigeration systems should have valid certification issued by the competent
At least one isolating switch of adequate size must be provided which sections each single phase and any
authority, and qualification for the treatment of the refrigeration system recognized by this sector. If
neutral cable. Or a removable and easily accessible power plug at the end of the installation.
another technician is needed for the maintenance and repair of the appliance, these must be supervised by
The system must be connected securely to an adequate earthing system as the failure to connect could
the person who is qualified for the use of the flammable refrigerant.
cause shocks, electric shocks or generate malfunctions to the units.
Install adequate section power cables before using the system.
Installation notes
Use only certified power and communication cables .
Make sure that the power supply matches the requirements of the system to be installed. A power supply
−
It is not allowed to use the air conditioner in a room where a fire has occurred.
of frequency and / or voltage different from the one foreseen or of unstable values, or incorrect wiring will
−
Drilling holes or burning the connection pipe is not allowed.
cause malfunctions to the system or damage to the units.
−
The air conditioner must be installed in a room that guarantees the minimum surface. The
Connect to a system power supply terminal is the / the cable / s phase, that the eventual neutral cable that
minimum surface is shown in table 1
the earthing cable.
−
Obligation to check for leaks after installation.
Make sure always to have interrupted the power supply before carrying out any work related to electrical
Table 1
connections and , i n any event , follow always all the relevant safety procedures.
Gas
Do not power the system before the installation is complete.
charge
If the power cord or communications cable is damaged no need to be replaced by qualified personnel.
(kg)
Keep distance or use special insulation between the power cables and the communication and the piping of
Pos.
gas because the high temperatures of the pipes could damage the cables.
floor
Minimum area
The system must be installed following the current regulations relating to electrical systems and systems
Pos.
of the room
with fluorinated gases .
Window
(m2)
The installation must be carried out in compliance with the requirements of IEC, NEC and CEC or equivalent
Pos.
and and exclusively by qualified personnel.
Wall
The air conditioner is the first class electrical equipment. It must be properly grounded with a dedicated
Pos. on
grounding device . The earthing system must have been built by professionals in compliance with current
the
regulations .
ceiling
During installation, make sure that an earthing system exists and that the units are connected to earth
Notes for maintenance
efficiently as electric shocks or electric shocks or malfunctions could occur .
The yellow-green cable identifies the grounding cable and must never be used for other purposes.
Check if the installation area or the room surface meets the requirements indicated on the label.
The earthing resistance must comply with current national electrical safety regulations.
−
It is mandatory to operate in an environment that respects the factory data and the data shown on
The switch or the power plug of the unit must always be easy to ccessibili by users at the conclusion .
the label
All power and communication cables must be installed by qualified personnel.If the power cable is of
insufficient length, replace it with one of adequate length. Do not ever joints more cables.
TEKNO POINT ITALIA S.R.L. - VIA DELL'ARTIGIANATO 5 - 30020 MARCON (VE) – ITALY
In installations that do not include the power plug , a disconnector installed on the line and a must be
provided .
Moving the air conditioner from one place to another must only be carried out by qualified personnel in
order not to incur physical injury or damage the units.
Provide always places the installation of the units outside of the reach of children or pets. If it is not
possible to install the units in safe places, it is necessary to provide safety protection systems (protective
grids or similar) that prevent children or pets from coming into contact with the units .
TEKNO POINT ITALIA S.R.L. - VIA DELL'ARTIGIANATO 5 - 30020 MARCON (VE) – ITALY
<=
1.3
1.4
1.5
1.2
/
14.5 16.8 19.3 22.0 24.8 27.8 31.0 34.4 37.8 41.5 45.4 49.4 53.6
/
5.2
6.1
7.0
/
1.6
1.9
2.1
/
1.1
1.3
1.4
COMMERCIALE@TEKNOPOINT.COM – WWW.TEKNOPOINT.COM
MUI_DELFIN_Ita_Eng_Fra_Deu_SKY/Rev.00/Data 03.06.2020
COMMERCIALE@TEKNOPOINT.COM – WWW.TEKNOPOINT.COM
MUI_DELFIN_Ita_Eng_Fra_Deu_SKY/Rev.00/Data 03.06.2020
1.6
1.7
1.8
1.9
7.9
8.9
10.0 11.2 12.4 13.6 15
2.4
2.8
3.1
3.4
1.6
1.8
2.1
2.3
43
41
ENGLISH
2.0
2.1
2.2
2.3
16.3 17.8 19.3
3.8
4.2
4.6
5
2.6
2.8
3.1
3.4
2.4
2.5
5.5
6.0
3.7
4.0
49
Werbung
Inhaltsverzeichnis
