Murray RDLT 22,0 Bedienungsanleitung Seite 25

Check Mower Blade Stopping Time
Mower blades and mower drive belt should come to a com-
Æ»ʻ ÉÊÅÆ Í¿Ê¾¿Ä Ì» É»¹ÅÄºÉ ·¼Ê»È ʾ» »Â»¹ÊÈ¿¹  ÉͿʹ¾
¿É ÊËÈÄ»º Å
¿Ê¾ ÊÈ·¹ÊÅÈ ¿Ä Ä»ËÊÈ·Â  º¿É»Ä½·½»º ·Äº ÅƻȷÊÅÈ ¿Ä
seat, start the engine.
Ľ·½» ʾ»  ·Äº Í·¿Ê ɻ̻ȷ ɻ¹ÅĺÉ
ʾ» 
¼ ÃÅÍ»È ºÈ¿Ì» ¸»ÂÊ ºÅ»É ÄÅÊ ÉÊÅÆ Í¿Ê¾¿Ä Ì» É»¹ÅĺÉ
see an authorized dealer.
Battery Maintenance
WARNING
:KHQ UHPRYLQJ RU LQVWDOOLQJ EDWWHU\ FDEOHV
GLVFRQQHFW WKH QHJDWLYH FDEOH ),567 DQG
UHFRQQHFW LW /$67 ,I QRW GRQH LQ WKLV RUGHU WKH
SRVLWLYH WHUPLQDO FDQ EH VKRUWHG WR WKH IUDPH E\
D WRRO
WARNING
Battery posts, terminals, and related accessories
contain lead and lead compounds - chemicals known to
the State of California to cause cancer, birth defects, or
other reproductive harm. Wash hands after handling.
Cleaning the Battery and Cables
1. Pull seat up to access the battery and cables.
2. Remove screws (A
(B
3. Slide the battery (C ¼ÅÈͷȺ ¿ÄÉ¿º» ʾ» ¸·ÊÊ»ÈÏ ¹ÅÄ-
tainer (D
4. Remove hardware (E ʾ»Ä º¿É¹ÅÄÄ»¹Ê Ä»½·Ê¿Ì» ¹·¸Â»
(F ¼ÈÅà ¸·ÊÊ»ÈÏ
5. Remove hardware (G ʾ»Ä º¿É¹ÅÄÄ»¹Ê ÆÅÉ¿Ê¿Ì» ¹·¸Â»
(H ¼ÈÅà ¸·ÊÊ»ÈÏ
»ÃÅÌ» ¸·ÊÊ»ÈÏ ·Äº Æ·¹» ÅÄ · ·Ê ÉËȼ·¹»
7. Clean battery container with a solution of baking soda
and water.
8. Clean the battery terminals and cable ends with a wire
brush and battery terminal cleaner.
en
¿É»Ä½·½»
¿½ËÈ» ·Äº ¸·ÊÊ»ÈÏ ¾Åº ºÅÍÄ
»·ÊÊ·¹¾ ʾ» ¸·ÊÊ»ÈÏ ¹·¸Â»É ÆÅÉ¿Ê¿Ì» ¹·¸Â» ÈÉÊ Ê¾»Ä
the negative cable using hardware.
10. Place battery inside battery container. Secure with hold
down and screws.
11. Push seat down.
Charging the Battery
WARNING
»»Æ ÅÆ»Ä ·Ã»É ·Äº ÉÆ·ÈÁÉ ·Í·Ï ¼ÈÅà ʾ» ¸·Ê-
tery; the gasses coming from it are highly explo-
É¿Ì» »Äʿ·ʻ ʾ» ¸·ÊÊ»ÈÏ Í»Â ºËȿĽ ¹¾·È½¿Ä½
A dead battery or one too weak to start the engine may
be the result of a defect in the charging system or other
electrical component. If there is any doubt about the cause
of the problem, see your dealer. If you need to replace the
battery, see the Cleaning the Battery and Cables section.
To charge the battery, follow the instructions provided by
the battery charger manufacturer as well as all warnings
included in the Operator Safety section of this manual.
Charge the battery until fully charged. Do not charge at a
rate higher than 10 amps.
If you need to replace the battery, see Steps 1-6 and 9-11 in
the Cleaning the Battery and Cables section.
Changing the Oil
Used oil is a hazardous waste product and must be dis-
posed of properly. Do not discard with household waste.
Check with your local authorities, service center, or dealer
for safe disposal/recycling facilities.
Remove Oil
¿Ê¾ »Ä½¿Ä» Å ¸ËÊ Éʿ ͷÈà º¿É¹ÅÄÄ»¹Ê ʾ» ÉÆ·ÈÁ
plug wire (D ¿½ËÈ»
spark plug.
2. Remove the dipstick (A
3. Remove the oil drain cap as shown in Figure 12. Drain
the oil into an approved container.
4. After the oil has drained, install the oil drain cap.
·Äº Á»»Æ ¿Ê ·Í·Ï ¼ÈÅà ʾ»
25