Belden Hirschmann RSR Montagehinweise Seite 3

Lieferumfang
incl. Montagehinweis
Bestellnummer
Wandmontageplatte, 150 mm Breite
Wandmontageplatte, 120 mm Breite
Wandmontageplatte, 90 mm Breite
Wandmontageplatte, 60 mm Breite
EN
Permission is not given for the circulation
or reproduction of this document, its use or
the passing on of its contents unless gran-
ted expressly. Contravention renders the
perpetrator liable for compensation for
damages. All rights reserved, in particular
in the case of patent grant or registration of
a utility or design.
Copyright
© Hirschmann
Automation and Control GmbH 2012
All Rights Reserved
Certified usage
Please observe the following:
The device may only be employed for the
purposes described in the catalog and tech-
nical description, and only in conjunction
with external devices and components
recommended or approved by Hirschmann.
The product can only be operated correctly
and safely if it is transported, stored, instal-
led and assembled properly and correctly.
Furthermore, it must be operated and
serviced carefully.
Recycling Note:
,
After its use, this product has to be
processed as electronic scrap and
disposed of according to the prevai-
ling waste disposal regulations of
your community / district / country /
state.
1 UNPACKING, CHECKING
Check whether the package was deli-
vered complete (see scope of delivery).
Check the individual parts for transport
damage.
z
Use only undamaged parts!
2 ASSEMBLY
For assembly you need (not included in
the scope of delivery):
- 4 screws
- 4 screw anchors, suitable for
the screws
- Drilling machine
- Screwdriver
Place the RSR wall mounting plate as a
drilling template on the wall, due to
your requirements, and mark the four
drill holes (see Fig. 1).
1 x RSR-Wandmontageplatte
943 971-004
943 971-001
943 971-002
943 971-003
Fig. 1: Mark the drill holes
Drill the 4 holes and insert the 4 screw
anchors into the holes.
Mount the device on the wall RSR
mounting plate as shown in Fig. 2:
Attach the upper snap-in guide of the
device into the rail and press it down
against the rail until it snaps into place.
Screw the wall mounting plate incl. the
device tightly onto the wall with 4
screws (see Fig. 2).
Fig. 2: Snap the device (here:
RSR20/RSR30) onto the RSR wall mounting
plate, screw it tightly onto the wall with 4
screws
3 DISASSEMBLY
To remove the device from the RSR wall
mounting plate,
unscrew the two lower screws on the
device (see Fig. 1 or 2).
insert a screwdriver horizontally under
the housing into the locking slide, pull it
(without tipping the screwdriver) down-
wards and lift the device upwards (see
Fig.3).
Fig. 3: Removing the device (here:
RSR20/RSR30) from the rail (RSR wall
mounting plate)
4 FURTHER SUPPORT
In the event of technical queries, please talk
to the Hirschmann contract partner respon-
sible for looking after your account or
directly to the Hirschmann office. You can
find the addresses of our contract partners
– on the Internet
(http://www.hirschmann.com)
Our support line is also at your disposal:
Tel. +49 1805 14-1538
Fax +49 7127 14-1551
Answers to Frequently Asked Questions can
be found on the Hirschmann product inter-
net sites on
www.hirschmann.com
The FAQs are located under „Service" in
the Automation and Control section.
www.hicomcenter.com
gives you an up-to-date overview of
training courses about technology and
products.
3