Herunterladen Inhalt Inhalt Diese Seite drucken

Specifications; Important Safety Instructions - Makita AN453 Betriebsanleitung

Pneumatischer coilnagler für innenausbau
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 16
ENGLISH
1.
Compressor air output per minute
2.
Nailing frequency (times/min)
3.
Pneumatic tool oil
4.
Adjuster
5.
Hook
6.
Contact element
7.
Shingle guide
8.
Shingle
9.
Projection
10. Adjust plate
11. Lever

SPECIFICATIONS

Min. hose diameter
Pneumatic tool oil
Dimensions (L X H X W)
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Note: Specifications may differ from country to country.
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
............. Read instruction manual.
............. Wear safety glasses.
Intended use
The tool is intended for the preliminary interior work such
as fixing floor joists or common rafters and framing work
in 2 "x 4" housing.
IMPORTANT SAFETY
INSTRUCTIONS
WARNING: WHEN USING THIS TOOL, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED
TO REDUCE THE RISK OF PERSONAL INJURY,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
• For personal safety and proper operation and
maintenance of the tool, read this instruction manual
before using the tool.
• Always wear safety glasses to protect your eyes from
dust or nail injury.
6
Explanation of general view
12. Magazine cap
13. Latch lever
14. Coil support plate
15. Graduation
16. Arrow
17. Feed Claw
18. Air fitting
19. Air socket
20. Trigger
21. Contact arm
22. Small rod
Model
Air pressure
Nail length
Nail capacity
Net weight
WARNING:
END101-1
It is an employer's responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
• Wear hearing protection to protect your ears against
exhaust noise and head protection. Also wear light but
not loose clothing. Sleeves should be buttoned or
rolled up. No necktie should be worn.
• Rushing the job or forcing the tool is dangerous.
ENE059-1
Handle the tool carefully. Do not operate when under
the influence of alcohol, drugs or the like.
• General Tool Handling Guidelines:
(1)
(2)
(3)
ENB090-2
(4)
(5)
(6)
(7)
(8)
• An improperly functioning tool must not be used.
• Sparks sometimes fly when the tool is used. Do not use
the tool near volatile, flammable materials such as
gasoline, thinner, paint, gas, adhesives, etc.; they will
ignite and explode, causing serious injury.
23. Ejection port
24. Nail
25. Humid
26. Hot
27. Brush
28. Drain cock
29. Air filter
30. Oiler
31. Pneumatic oil
32. Thinner
33. Stove
AN453
0.44 - 0.83 Mpa (4.4 - 8.3 bar)
19 mm - 45 mm
120 pcs.
6.5 mm
Turbine oil
265 mm X 269 mm X 117 mm
2.4 kg
Always assume that the tool contains fasteners.
Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
Do not activate the tool unless the tool is placed
firmly against the workpiece.
Respect the tool as a working implement.
No horseplay.
Do not hold or carry the tool with a finger on the
trigger.
Do not load the tool with fasteners when any one
of the operating controls is activated.
Do not operate the tool with any power source
other than that specified in the tool
operating/safety instructions.

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis