Herunterladen Inhalt Inhalt Diese Seite drucken

Start-Up - Parkside PISG 80 A1 Originalbetriebsanleitung

Inverter-schweissgerät
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Start-up

Note: The welding tool is suitable for welding with
electrodes.
Use electrode retaining clips without protruding
retaining screws meeting today's safety stand-
ards.
Be sure the ON / OFF switch
tion "O" ("OFF") or the main supply cable is
not plugged into the mains socket.
Connect the welding cables according to po-
larity and electrode manufacturer instructions.
The welding circuit should not be intentionally
be brought into direct or indirect contact with
the safety cable unless on the welding part.
When intentionally welding to the workpiece
via safety cable, the connection must be as
short as possible.
The cross-section of the safety cable must be
at least the same cross-section as the welding
current return cable.
Both cables must be connected to the workpiece
in the same location. Use the earthing lug on
the tool or a nearby earthing lug.
All safety measures must be taken to prevent stray
current. Verify the mains voltage of the input
voltage matches that of the tool (see type plate).
Put on suitable protective clothing according to
provisions and prepare the work area.
Connect the earth terminal to the workpiece.
Secure the electrode in the electrode holder
Switch on the device by setting the ON / OFF
switch
to the "I" ("ON") position.
9
Set the welding current with the control knob
according to the electrode used.
Note: Please see the table below for the weld-
ing current according to electrode diameter.
Attention: When welding with electrodes
(MMA), the electrode holder and the earthing
lug must be connected to positive (+) or negative
(-) according to the welding rod specifications.
1.6
2.0
2.5
270751_Inverter Schweissgeraet PISG 80 A1_content_CZ.indd 11
is set to posi-
9
.
5
3
40–55 A
55–80 A
80–100 A
Hold the welding shield
and begin welding.
To stop working, set the ON / OFF switch
the "O" ("OFF") position.
ATTENTION!
If the thermal overload protection is automatically
triggered, the yellow control lamp
However, if the overload protection is triggered and
the power supply for welding is energised, the yellow
control lamp
will be on, but you will be unable
2
to weld.
ATTENTION!
Be careful not to rub the welding rod against the
workpiece. This could damage the workpiece and
make it difficult to strike an arc. Maintain the proper
distance to the workpiece after striking the arc. The
distance should correlate to the diameter of the
welding rod used. Maintain this distance as accu-
rately and consistently as possible whilst welding.
The angle between the welding rod and the working
direction should be between 20 and 30 °.
ATTENTION!
After welding, the welding clamp and the welding
rod must be set down on the insulated holder. The
fusion slag can only be removed once the rod has
cooled down. To re-weld the interrupted weld, the
fusion lag must first be removed from the welding
position.
ATTENTION!
The welding tool is protected from overheating. The
control lamp
flashes if the overheat protection is
2
triggered. In this case, switch off the welding tool and
allow it to cool down briefly.
ATTENTION!
If the power output cable is too long, a power drop
may occur or the weld could be poor.
ATTENTION!
Ensure a stable voltage. Power fluctuations can
affect welding.
Start-up
in front of your face
7
to
9
will be off.
2
GB
11
27.01.16 15:00

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Ian 270751

Inhaltsverzeichnis